Recent content by 20pilot

I am in need of a new manifold for my 5.7 crusader. I am having trouble finding the part, crusader part number 7151100. I can't not source this part anywhere. Most shops tell me its to old and they don't handle parts for this engine. It runs great, just has some rust and I would like to change...

Does anyone know the replacement part number for a VOLVO SX-M1? I need to replace it and would like to have it before I pull it all apart. Any help would be greatly appreciated. Thanks

Can someone tell me what Volvo drive this is?

Coming off my Manifold/Riser I have a down pipe. I replaced the manifolds and risers about a year ago, but not these pipes because I could not locate them. Of course, one of them developed a pin hole so I would like to replace both. Its on a Mercruiser 350 Fuel Injected. Attached are a couple...

I have a inboard mercruiser 5.7 with a throttle body. I have been having an overheating issue so I started with all of the main parts: Raw Water Pump, replaced impeller New Circulating pump Heat exchanger boiled and pressure tested New Manifolds and riser Inspected all hoses, no restrictions...

Can anyone help identify what drive I have: Engine: 0F800890 Transom: 0F832761 Drive: 0K096819 The boat has been in the water for about 6 years straight with no protection to the outdrive. It looks like electrolysis got the best of it and I need to replace the entire drive. There is nothing on...

Mercruiser water pump Does anyone know if there is an aftermarket (Sierra, EMP) replacement pump for pt #46-807151A8

I am currently looking to install a mercruiser engine into my boat, however all of the motor/transmission mounts are frozen and need to be replaced The engine is a carb'd mercruiser 350. Its an older engine early 90's that was just recently rebuilt. Its going into a straight inboard application...

Added controls and rigging to my second station and I am having gauge trouble on my 350TXR. The issue I am having is the gauge that I bought is not matching up to the harness. The plug I have coming to the gauge is bigger than the input on the gauge. I was sold a 6Y8-8350T-01. I do have the...

I found a crack in my distributor cap on my mercruiser 350. Could someone please identify the cap? The only markings say Delco-Remy, not part number or anything. I have never seen one with the box on the top. I don't have any model number on the engine, it was just a rebuilt 350 with aluminum...

My steering ram started to leak and I am looking to replace the seal. I showed the ram to several people and no one was able to identify what seal kit was needed. I knew that you guys would have the answer for me or point me in the right direction. I am attaching several pictures which may help...

I am currently rebuilding my inboard Mercruiser 350 engine. I ordered a new Edelbrock 2506 Aluminum intake and I am having a problem matching the gasket. I was told the Sierra 18-0868 was the correct one. It is correct other than the water jacket is square on the intake and round on the new...

Hey Guys. My father purchased a 1966 41' Hatteras Conv. with a Isuzu Marine Generator. The genset ran good for the first few times we used it. However, this passed trip the generator stopped putting out power. I am not able to find a model or serial number on it anywhere. I had a mechanic...

I have been trying to research manifolds and risers for my 305 Mercruiser 5.0 MPI, serial number OM669371. Seems I am not able to locate any though Sierra or Barr. Would anyone know the part numbers associated with the manifolds and risers for this engine? Thanks

I am looking at purchasing a boat with a 1990 Yamaha 225HP EXTD. I was planning on doing a compression test. Motor was rebuilt 6 years ago, owner estimates 300/400 hours. Is this the correct way: Pull all plugs, test each individual cylinder during a cold start with boat in neutral? Someone...