Recent content by 66Holiday924

  1. 66Holiday924

    1966 Starcraft Holiday Interior Work

    I ended up having the Holiday painted last year. They did a pretty good job. The last thing, that I wanted to do, to finish the boat was replace the rubrail rubber insert. Doing a couple laps around iboats, I've gathered that Wefco 0101G is the correct insert for my rails. I'm a little nervous...
  2. 66Holiday924

    1978 Islander 22 I/O

    I took apart the windows. The side windows aren't cracked or broken or anything, the front cabin window is though, and the plan is to have it remade, and I want all of the windows to match so I'm going to have them all rebuilt. I'm leaning toward a dark tint plexiglass, something that makes it...
  3. 66Holiday924

    1978 Islander 22 I/O

    That's pencil... I'm talking about zooming in and looking at the teak string the engine is sitting on.
  4. 66Holiday924

    1978 Islander 22 I/O

    You can see it on the Port Stringer if you use the zoom function.
  5. 66Holiday924

    1978 Islander 22 I/O

    What @Watermann said. It's not going to rigidly connect to the boat. RDS explained that they typically like the tank to be able to move a little bit, about .25" or so. So, it's going to be boxed in just like Watermann's picture. I'm going to put aluminum strips across the top of the stringers...
  6. 66Holiday924

    1978 Islander 22 I/O

    Well, two steps forward and one step back... The Islander is at a fabricator shop. I'm having a new piece of trim that goes across the top of the stern sheet made, mounts for my boat buckles added to the trailer, and new skin cut for the transom cap and gunnels. Starcrafts from this era had an...
  7. 66Holiday924

    1978 Islander 22 I/O

    The fill will be 2" off of the front end of the tank and it will stick up a total of 2" off of the tank. I am raising my deck 2" to accommodate, so it and the fill hose can be run under the deck. It is going to be run as directly and almost exactly how the original tank hose was run, a 90 degree...
  8. 66Holiday924

    1978 Islander 22 I/O

    I was advised to make a mock-up of the custom fuel tank I have been discussing with the fabricator RDS, through Tank & Barrel. They are very responsive if you call them. They can build just about any tank you want too. My tank is a basic belly tank, but the dimensions change forward to aft due...
  9. 66Holiday924

    1978 Islander 22 I/O

    I have daughters so it's a must for me. I totally plan to continue using a pee jug for men and asking them to please not take a $hit on my boat. This is probably a good moment for an FYI, public service announcement: Nobody wants you to take a $hit on their boat. Please avoid if you can. In my...
  10. 66Holiday924

    1978 Islander 22 I/O

    I got the rest of my corrugated polypropylene sheeting in. I used the HVAC tape to tape it down. I'm happy with the tape on applications like this. It adheres very well and being HVAC tape it has a huge temperature range. The plates in front of the cabin are for my batteries, two batteries...
  11. 66Holiday924

    1978 Islander 22 I/O

    Yeah, it's getting to the point that I'm going to have to shut it down for the winter pretty soon. I'm not planning on putting anything under the grates, no pan, no floatation foam, nothing. It'll be open air to the bottom of the boat. The grates will be in-between two ribs, so should...
  12. 66Holiday924

    1978 Islander 22 I/O

    The weather has been rainy, so it's been slow moving but I am making some progress. I decided that I am going to copy what I did with my Holiday for floatation. First, I span the ribs with corrugated polypropylene sheets. This creates a void for water to move freely, under the sheeting and...
  13. 66Holiday924

    1978 Islander 22 I/O

    I don't know how it would hold up to water. It shouldn't get wet where I used it and eventually it's going to have vinyl flooring over it anyway.
  14. 66Holiday924

    1978 Islander 22 I/O

    Getting her put together a day at a time. I reinstalled my stringers, cleaned up the cabin bench aluminum, added some built-in tackle storage, and I ordered some more Coosa to play with. I patched over some old vent holes in my cabin-bench aluminum with HVAC tape (piece on each side). I think...
  15. 66Holiday924

    1978 Islander 22 I/O

    A big milestone for this project!
See more
Top