Recent content by Andrik

  1. A

    Engine warning light Evinrude Ficht RAM 2002/2003

    The problem with code 43 was a frozen cooling lines. RegardingCode 27 12 V circuit above range, the error probably was in the EMM. I switched to another EMM from an 2000 model, programmed it with the right injectors, and now it is running well without error codes. Will probably test it on water...
  2. A

    Engine warning light Evinrude Ficht RAM 2002/2003

    I'm unforunately still not out fishing... I decided to have a last test before boating to see that the water is passing through the motor. It's -7C outside, and I feared frozen hoses . There was no water coming out as I feared. I used warm water, filled warm water up to the waterintake for a...
  3. A

    Engine warning light Evinrude Ficht RAM 2002/2003

    SOLVED The resistance testing was wrong, the sensor was in working and have the right values. The problem making the code 47 and code 48 was the black cable to the air temperature sensor. I had not tested the voltage between the black and purple/blue wire, but between ground and the purple/blue...
  4. A

    Engine warning light Evinrude Ficht RAM 2002/2003

    Update: None of the other injectors was programmed in the EMM... I programmed them, and then the motor fired up easily The compression is good, 123-123-132-132 psi Still get the same error codes and the check engine alarm EV Dialog tells me to check the blue/purple wires and ground TESTING: ATS...
  5. A

    Engine warning light Evinrude Ficht RAM 2002/2003

    Thanks, the seller told me that the engine was in good condition, and that the reason it was dismounted was because the lower unit was damaged due to running aground. He said it had good compression. I have two other 115 EMM's without any fault codes, but I am unsure if they are pre 2002 or...
  6. A

    Engine warning light Evinrude Ficht RAM 2002/2003

    I have bought what should be a Evinrude 115 Ficht RAM complete powerhead with all components. It must be a 2002 or newer, since it has a newer oil lift pump than the pre 2002. When I tried to fire the enginge up today, it shut down after some attempts, and the third warning light on the system...
  7. A

    Oil injector/manifold routing Evinrude Ficht RAM 90 hp 2003

    Thanks a lot, Crosbyman. Then the problem i is solved. I have checked, and this is the line to be connected to the fuel line. I found a T that will come by post. For to not have to wait, I clogged the cut oil line and mixed in Oly's brew to try to start the motor today. Got an engine error code...
  8. A

    Oil injector/manifold routing Evinrude Ficht RAM 90 hp 2003

    Thanks a lot! This was helpful. So the right thing to do is to buy a "T" and connect it to the main fuel supply that runs into the lift pump?
  9. A

    Oil injector/manifold routing Evinrude Ficht RAM 90 hp 2003

    Hi I have swapped my 2000 90 Ficht RAM with an 2002 or 2003 Ficht RAM. There is the newer oil distribution system, with one more oil pipe connected to the oil mainfold,. I guess four of them are to each cylinder, but unfortenately the previous owner cut the pipeline that runs under the fuel...
  10. A

    Change from internal to external oil tank Mercury 2-stroke 90 hp 1995?

    I wonder if the oil pump on my Mercury 2-stroke 90 hp 1995 will manage to pump the oil up from an external oil tank? Then I will get rid of the traditional leakage from the top of the tank when the motor is tilted. Does the gravity in the integrated tank have some effect on the oil flow, or wil...
  11. A

    Sneezing at idle when starting after 30 min pause

    I have an odd idle-problem with my 150 98`Ocean Pro. It starts and runs very well at idle and full speed when motor is cold. When hot, it also starts and runs good at idle and full speed. BUT; When motor have been shut off for 30 min, it is impossible to run well at idle. It starts, sneezes and...
  12. A

    Props for Sunbird SWL 203

    I have changed motor from Evinrude Ocean Pro 175 to 150 on my Sunbird. The prop on the 175 was a Raker 14 1/2 x 20, the prop on the 150 is an ordinary 14 1/2 x 21+. Which one will be best for my Sunbird SWL 203? I have noe experience on this.
  13. A

    Colour code Sunbird SWL 203

    I am going to paint my Sunbird SWL 203 back to its original colour. Does anyone know the colour code or the name of the white colour for the top coating on this boat?
  14. A

    Colours wiring evinrude ocean pro 159

    Does anyone know where these two cables (with three wires) shall be connected on the dashboard? I know purple is for the ignition switch, but there already is noe in the 6-pin connector to the switch.
  15. A

    Leakage from o-ring fittings fuel pump Evinrude Ocean Pro 150 98`

    I have a leakage from the o-ring fittings on the top of the pump into the fuel bracket on my 150 Ocean Pro 98`. It starts to flow at once when I try to start the motor. It is not possible to get the hand pump hard, the gasoline will just flow. I have tried to put on new o-rings, but the problem...
See more
Top