Recent content by bcclew

  1. B

    p c v valve?

    used to have crusaders now i have 5.7 chev long blocks edelbrock intake and edelbrock carbs i am wondering why these engs never use pcv system? inoticed a lot of soot on choke plate. comming from valve cover vent hose too flame arester.so again i am wondering why not a pcv?thanks for any help
  2. B

    garmin 541s

    going over the same route over and over it leavs a red track line on the screen. i have looked in the book and mabe i just dont see it. i tried to save the one route and erase the rest but i cant seem to find out how it says do you want delete tracks?witch i tried but it gets rid of all...
  3. B

    Crusader 1976 temp and oil pressure alarms?

    im trying to figure out should these senders or switchs depending on what site you go too? with the eng off oil presure swith creates a ground corect? temp switch should be ol no ground with eng off right?with eng on the temp sender or switch should create ground when eng starts too get hot mabe...
  4. B

    wireing harness

    1979 johnson i need the harness from the helm to the motor its a 17 foot center consol mabe 10 ft long havent taken the old on out yet.new or used any body got one? or where to get one.they seem to be discontuied.thanks
  5. B

    aqua tach

    1976 silverton is useing aqua tachs. any body know if there still in busines?i looked on line dont seem to be.heres my prob need new tach.3 inch hole the ones i see that say 3 inch are not they are 3 and and 1 eighth i have tried faria and telaflex.had to send them back as you know this is...
  6. B

    fuel pressure tool

    where can i get the fitting that goes on the sherader valve on and efi?my kit has every thing but that one thanks
  7. B

    looking to buy gps

    whays out their not a crazy amount of money?chart planner and transducer?thanks for the help//////
  8. B

    1976 silverton prop shaft

    prop shaft after looseing the set bolt on the v drive flange how tightshould the shaft be?i was able too pull it back kind of easy i have heard it should be like and interference fit? IS this true?also the shaft is brass and the dimple for the set screw is kind of long gated can this be...
  9. B

    12 volt ac units

    has anyone installed one of these 12 volt systems?i see theirs a lot on line.some use and inverter some you need extra batts but theirs one that uses three compressors they shut down one at a time than matains temp with one just wonder if anybodys seen or used them thanks
  10. B

    honda 225 4 stroke overheating

    ok guys help starboard side exhaust man running hot 202 with heat gun setting off buzzer relief valves have been changed new thermostats 60c still hot took out thermo and disconeted hose from thermo and small hose on bottom of ex man started eng water flows fine put hoses on ran still 202 took...
  11. B

    kohl gen

    looking for wireing dia for kohl gen ce96 model 65esz the boat that it came out of was a fire job but it runs fine i am looking for a dia that shows how it hooks up to the boat for starting and running i tried looking one kohl but didnt seem to be much help thanks/////
  12. B

    kolh genarater

    any body know where to get a wireing dia 65esz any help would be great need the dia that goes from gen to boat wireing and starting circuit thanks
  13. B

    gps

    whats a good gps not too many$$dont know much about marine typewith out street signs how do they work esp atnight thanks lew
  14. B

    tps

    225 hp 1999? voltage should be .950 to 3.75 app, my understanding is voltage should increase as throttel is opened this eng was worked on before i got it tps seems to be mounted corect small coupler can go 180 either wayhears the prob voltage will decrease going to open throttel wire colors seem...
  15. B

    tack

    2005 200 yamaha out board tack problem new tack is set to 12 same as old one was also set to 12 it did not work either on back of tach purple wire is hot 13.5 volts engine running black ground is good gray signal wire 6 volts running tach dose not work i am looking for the proper way too check...
See more
Top