My low pressure pump is noisy and it’s had a couple hard starts every once in awhile. I’m having it serviced at a shop and he is saying to replace the whole fuel pump kit assembly. He said my pressure and vacuum checks out on both high/low pumps, but to be aware it could give out anytime. The...
I have always noticed a squeal from the belt and started replaced the alternator, idler, tensioner. I put a new belt on too. Now the new belt slips off the water pump pulley by a tooth. I have read that the PS pump is to blame, and it does look about an 1/8” in front of the water pump pulley...
I cant seem to find anything about using this zerk fitting for the gimbal bearing. The service manual says to fill seasonally, but it also says to remove the drive when filling...?
I need to run all new wires on my 20ft boat trailer. I cant find any wirings kits and suppose Im supposed to buy the 7 pin connector (or 5 pin flat if you prefer) and then buy some marine grade wire spool to connect and run down the rails of the trailer? What kind of connectors do you use? I...
I recently drug some rocks at modest RPM/speed and am a bit concerned, naturally. I had a skeg cover which took some good impacts. After getting the boat out of the water, I have the drive in full up position, and I can lift the drive another 1/8th in or so. I've lifted the drive before and...
Ive got a 2006 Larson Senza 206 that I use for towing and cruising. The recommended WOT ROM range is 4600-5000. I have a 14.5x17 4 blade aluminum that WOT RPM is at 4500 and about 40mph. My 15x16 4 blade aluminum was WOT at 5100 RPM (I had to pull off a smidge to keep it at 5000). I need to...
I just replaced the shift cable and am having trouble understanding how it goes back together with the trim switch cable. It is long like your supposed to wrap it around the hub that the remote arm mounts to. I can’t seem to find anything online and the part diagram doesn’t help...
I have a 2.25A light that I want to connect to a string of low wattage LED lights (about 3A). I dont want to overload the thin 16 guage wire the string of lights are on. So I want to connect the 2.25A light directly to the battery but then have it turn on and off using the string of 3A lights...
I bought my first boat and wasn’t sure of the condition of the bearings so I pulled them. They looked good and had good grease. The bearing buddies kept the water out.
My question is how do I go about flushing the bearings without removing the hub? I’ve got disks with thread locked slide bolts...
Im mounting a small 1x2 piece of pine wood to the back of the seat in the engine bay. I cant put screws through as it will be seen from the inside of the boat. I painted the wood with white interior paint and planned on gluing it to the fiberglass. It is about 10" from the front of the...
I need to replace my shift cable, but cant seem to find any specific replacement parts, I see different lengths and am not sure how to find out which one you need. Do I need to pull it out first? Ive got a 2006 Larson Senza 206 5.0L GXi-F with SX-M1 drive
ive got a 20' tandem axle with disk hydraulic brakes actuated by the tongue. I cant seem to find solid maintenance information, is there anything outside of flushing the brake fluid?
The caliper also is completely loose. You can grab it and shake it about 1/8", the pad opposite the piston also...
Im unfamiliar with this steering system, but familiar with mechanics. My steering doesnt feel great but seems to be working fine. Can anyone explain why this hydraulic pump that comes after the steering cable moves? Is there any thing I can check that are common issues with these systems? Here...
Just bought a 2006 Larson with 160 hours on it. I read that the screen on the fuel pressure regulator has caused pump starving issues and a tech bulletin to remove was sent out. I pulled it out and ironically after about 1 hour of use, I had some issue with the EFI system.
I do want to note...
