Recent content by bigbill239

  1. B

    Looking for outboard salvage yards

    Im looking for used etec parts anyone know of any salvage yards the part Im hunting is a tiller handle part BRP5007125 its blue but white will work with a little spray paint 75hp and 90 hp same thing
  2. B

    90 Etec how to start on eng. Stand

    Does anyone know what parts and part numbers I need to start a 90 e-tec on the stand? I know there has to be somthing I can put together to start it on the stand. Any help would be appreciated:confused:
  3. B

    How to hoist E-Tec (lifting points)

    I have a 2008 90 hp Evinrude E-Tec. I need to lift the motor off of a pallet and put it on a stand. But I can't find any place to lift it. I have a engine hoist but can't find any place to hook anything to. Does anyone have any experiance with picking up a Etec any help would be appreciated...
  4. B

    2008 Etec 90hp remote Jet unit

    Any ideas on switching a Etec 90 hp remote to a tiller handle I have been told a cpl of conflicting stories one place says no problem the other place says cheaper to get a new motor
  5. B

    E-TEC Computer program INFO needed

    E-Tec is totally ran off of the computer program if I?m not mistaken similar to that on a Cummins or Detroit diesel in a semi truck you can hook it up to your lap top and everything you want to know about that motor just spits right out like a tattle tale. Where can the common laymen buy the...
  6. B

    Evinrude E-Tec Value ? NADA

    I was trying to find out the value of a 2005 90hp E-Tec model # E90DPXSOR the variations is driving me crazy now I think I know less then when I started any other place to look for outboard values would be appreciated thank you
  7. B

    X-long shaft need to shorten

    :confused:I came accross a Xlong shat 25in E-tec problem is I need a short shaft what kind of hassel am I looking at Im changing from prop to jet unit. Even with a transom extension Im still to long :confused:
  8. B

    Water Fuel Separators 10 Micron vs 12 Micron

    I see all of these water fuel separators claiming to be top quality some have 10 microns some 12 microns. What is the difference between a 10 micron or 12 micron what is the better of the 2
  9. B

    Water fuel Separator filter replacement (help)

    When replacing a water fuel separator filter canister. Its been so long since I did it. I know to clean the surface of the mount and put a light coat of oil on the rubber gasket. But I can?t remember if you fill the canister with gas or not someone refresh my old memory
  10. B

    3 hp. Merc made in Japan Parts & Year ?

    I have a 3 hp Merc I?m trying to find the year does anyone know where to look and also I need a coil but when I look on I boats its not the same one as they have listed. Serial #CA873358 model # it's either 306 or 3D6
  11. B

    Johnson 9.9 hp. prop help (late 70s)

    I have a late 70s 9.9 hp Johnson I don't know how tight to put the prop nut on. When I got the motor the prop nut was loose with a cotter pin holding nut on should it be torqued down to a specfic tourque any help would be apprecited thanks Bill
  12. B

    jet unit for mercs

    Does anyone know a wholsaler for jet units or a resnable place to order a jet units
  13. B

    Can anyone tell me what the difference is in prop pitch

    I have a 90 hp Merc it came with a 15 and a 17 pitch prop what is the difference?
  14. B

    1979 90 hp. Merc. Waterpump help needed

    I have never worked on boat motors except to change plugs and coils.Can anyone tell me how to change out the water pump and maybe send a link to a blow up picture with instructions. So a novice can do it. Thanks Bill
  15. B

    1978 55hp Evinrude spark plug gap?

    I have a 1978 55hp Evinrude can anyone tell me what the plugs should be gaped at? Or where to find out I had ordered a manual but it's not here yet and I want to go fishing.
See more
Top