I just finished rebuilding the lower unit on '95-96' Johnson, 115hp. It uses single seal, dual lips on both prop seal and driveshalf. I took the seals out previously, so I can't remember the directions if I am installing it correctly. Both seals have an extended lip. Manual says to install...
Hi all - I am having an issue where I can't get past 3500 RPM when trying to plane the boat. Even with the full throttle pushed down, it seems to max out at 3500 RPM and seem to struggle. Only when I bring up the engine by trimming it up, it would go to about 4000 RPM, but that's it.
I doubt...
I ordered a new CDI power pack and it comes with a thick plastic film over the RF shield. Was wondering what's it for and should I remove prior to installing. Thanks.
I ordered two spring sets of 1750lb rating each, 4 leafs total per spring. However, on the old one at the slipper end, it has two leafs, as oppose to the new one having only one leaf. Is it okay to use the new one? On the trailer, the slipper end touches the frame, and a long screw right below...
'96 Ocean Runner 115hp performed flawlessly all season. In fact, took it out yesterday on last trip but didn't flush out engine with fresh water since I came home late. It had no issues on the water.
This morning, starts right up for 15 seconds, then dies. Now it wouldn't idle for more than...
Engine has always performed very well. We took her out just last week at the same boat ramp with no issues. This morning,
all of the sudden the NO OIL alarm went on ( Beeping every 1-2 seconds) after I took off from the ramp. Immediately, I turned the key off, check the oil injection tank primer...
Re: Power Trim not responding, able to hear relays on engine clicks
Just saw a small hole in motor housing itself, all rusted around there. I check the reservoir and it is still redish. Do I have to replace everything or just the motor itself ? It has four screws on it, so I assume you can...
I was getting ready to hit the water today and the power trim tilt is not working. I tried to replace with different relays on the engine ( 95 Johnson OceanRunner 60 degrees 115hp). I hear both on them clickings when pressing up or down button, but the trim doesn't response. Battery is okay...
Does anyone know why the spark plug keeps expanding after a few usage? I suppose this is normal due to combustion. I gap to .030 for the Champion QL78YC. After a few times out, its now like .040+. Should I regap it back to .030 or leave it? Thanks.
Engine will not start unless I manually flip the red handle choke/primer(term?) behind the air silence up (not sure if cold weather lately have to do anything with it.) If I manually choke the engine by pushing in the key when starting, it would just cranks and cranks. However, flipping the...
Searched a few topics but didn't seem to find my answer. I have a dual batteries with Perko switch selector. The batteries are the exact same. Question is when starting an engine, should I turn to DUAL or choose a battery randomly. Once started, can I leave it in DUAL to charge both batteries...
I've been using the Champion 938m spark plugs (QL78YC). However, when I look at the OEM manual (not sure if its for '94 series engine or '95), it specifies the QL77QJA (also known as 838m Champion spark plugs.) Can someone chip in and let me know which one is correct one to use on this engine...
I've been trying to adjust my idle screw on on this engine with no luck( Johnson J115SXEO). It originally came with 9 screws turned out from closed position. But from the manual, it recommends 2-3 or so. I adjust it to 5-6 turns from closed position just from listening to the engine. Does anyone...
Re: bunk bracket, is this safe to install
LippCJ7, thanks for explaining. I've included a picture. I believe this is what you guys are recommending if I have a C beam correct? Idea is to let the bumps latch on the open side of the C beam?
(RED is the U Bolt, circles are the nuts.
If my...
I am planning to replace the bunks and the brackets holding them. They no longer carry the style with the holes as shown on the right (more reliable in my opinion, can't slide anywhere). Instead, just the one on the left. I am worry once the boat is loaded, the bracket will be pushed down due to...
