Current visitors

Home
Members

Bondo's latest activity

Bondo reacted to redneck joe's post in the thread How Can I Prevent Fouled Spark Plugs When Running at Idle for a long time? with Like.

Im no expert but that sounds like a carb adjustment problem.

Dec 16, 2025
Bondo reacted to Bugzilla46310's post in the thread Pump themed anchor with Like.

Obviously you did not read the whole post.

Dec 13, 2025
Bondo replied to the thread Pump themed anchor.

Ayuh,.... Welcome Aboard,..... I love it,....... I've spent my life, turning junk into gold,....

Dec 13, 2025
Bondo reacted to redneck joe's post in the thread Pump themed anchor with Like.

Looks pretty cool. I retired yesterday from being semi retired because of my first grandbaby that came Wednesday. I am now a full...

Dec 13, 2025
Bondo reacted to alldodge's post in the thread recmnds for 2.5" fuel filler hose under my console with Like.

You do want to measure the Inside Diameter (ID) not the Outside Diameter (OD) for hose selection

Dec 13, 2025
Bondo reacted to Scott Danforth's post in the thread 1990 OMC 4.3L No-Start Condition :*( with Like.

first, welcome aboard next, step back and put the wrench down yes, all the pushrods are the same length. and you set the valvetrain...

Dec 12, 2025
Bondo reacted to tpenfield's post in the thread Fiberglassing Technique Video with Like.

I've been meaning to make a video about the fiberglassing technique that I use. Since I am doing quite a bit of fiberglassing right...

Dec 12, 2025
Bondo reacted to alldodge's post in the thread Removing gas from an old sportfish while in the water? with Like.

Guess I'm missing something Why not wait for it to get on the hard and then do something with fluids. Is it in danger of sinking now?

Dec 12, 2025
Bondo reacted to Scott Danforth's post in the thread Removing gas from an old sportfish while in the water? with Like.

pull the inspection cover over the tank pull the fuel sender and pump out thru the sender hole. then you can clean out the tank thru the...

Dec 12, 2025
Bondo reacted to Scott Danforth's post in the thread recmnds for 2.5" fuel filler hose under my console with Like.

Are you sure on the size of the A2 hose? Most marine fuel tanks are 1-1/2" I'd for gasoline and 2" for diesel. On an 18' boat I would...

Dec 12, 2025
Bondo replied to the thread looking for recommendations for gimbal bearing puller.

Ayuh,..... Ditto,.... 'n a rear wheel bearing puller end, from OTC, which allows to slip it in behind the bearing, 'n then flips...

Dec 8, 2025
Bondo reacted to Jmunk's post in the thread looking for recommendations for gimbal bearing puller with Like.

I just use a slide hammer.

Dec 8, 2025
Bondo reacted to DeepCMark58A's post in the thread Winterizing for in water - engine raw water drain with Like.

So does the rest of the world.

Dec 5, 2025
Bondo reacted to Fun Times's post in the thread Merc Service Bulletins with Like.

On your note I reached out to a now long term iboats member that still happens to work at a Merc dealer to help check on this topic for...

Dec 4, 2025
Bondo reacted to bruceb58's post in the thread 1989 OMC Cobra exhaust seal with Like.

You must not be in salt water then. Batwing manifolds were hard to cast properly so they easily got thin spots. You might have gotten...

Dec 2, 2025

Show older items

Home
Members

Top