Recent content by BowPro

  1. BowPro

    Lowrance Elite FS 9

    I didn't know they ever made a noise until I was informed recently that they do, and could hear it up close. It's a faint pulsing tick when up close. I'm confused now. lol. I am though gonna try a hard reset when I'm on the water and see if anything changes. I have no info saved on the machine...
  2. BowPro

    Lowrance Elite FS 9

    Bought a boat and this sonar came with it. Tried a reset, uploaded the latest software version, and played with all of the settings to no avail. The down scan is a snowy haze as well. The transducer is the 3 in 1, as shown on the tag of the transducer cord, and it is also showing as a 3 in 1...
  3. BowPro

    E70TLEDA Primer Choke

    Good deal. I pulled up the part numbers off the evinrudeparts.ca and just bought the OEM stuff from crowleymarine. I appreciate it.
  4. BowPro

    E70TLEDA Primer Choke

    Yes Sir, it looks pretty simple. It's hard to determine what OEM is, being that nothing visibly says so. I see a Sierra brand here on Iboats, and also Sierra on Amazon. Do you think this would suffice? If you have a suggestion, or a direct link to an official OEM kit, I would appreciate it...
  5. BowPro

    E70TLEDA Primer Choke

    I believe I found it. Would this be all that the replacement parts require? It appears to be leaking past the o-ring that's on the manual choke lever. It looks like this contains the new o-ring, along with a new manual choke lever...
  6. BowPro

    E70TLEDA Primer Choke

    Is there a rebuild kit for the existing primer choke I have, or do I need to just buy the whole new part? It appears the replacement part number used to be 0437238, but now replaced by 5007356. It leaks fuel. If there is a gasket rebuild for this, I'd rather just do that, but I can't seem to...
  7. BowPro

    1990's Evinrude 70 horse

    I got the Model and Serial and its a 1996. Yes Sir, the plugs in it were what it called for. Every local part store in my town said they had to special order them. I found this site and it shows an NGK cross reference and recommends them over the Champion. "EVINRUDE/JOHNSON MOTORS SHIP WITH...
  8. BowPro

    1990's Evinrude 70 horse

    That's kinda what I went by on google images. I see the motor tag now.
  9. BowPro

    1990's Evinrude 70 horse

    Ahhhh Bet! I see it. Thank you. That'll get me going now.
  10. BowPro

    1990's Evinrude 70 horse

    I just looked up model number locations. If it's on the side like I'm seeing, I don't recall seeing a tag. I don't see any on the pics that I just posted of both sides of the transom.
  11. BowPro

    1990's Evinrude 70 horse

    Cool deal. I'll check it out when I get home this evening. Is it visible with motor down or do I need to raise trim and look underneath?
  12. BowPro

    1990's Evinrude 70 horse

    Here's the outboard
  13. BowPro

    1990's Evinrude 70 horse

    Where can I find the model number on the outboard?
  14. BowPro

    1990's Evinrude 70 horse

    My son got a free boat for cleaning all of the garbage out of it and cleaning out a small barn full of garbage. Got it prepped, steering cable unseized, Sea foam deep creeped the cylinders, pulled the carb bowl screws and pumped Seafoam until the crud was removed and Sea Foam drained, etc. Rolls...
  15. BowPro

    Powerhead Down!

    2005 Evinrude 225 HO DI. Running down river and lost a lot of power, it slowed down immediately, and I could hear knocking. I shut it down and then tried to start it just to see what it would do. It was locked up. About 5 minutes later, after cooling down, it started up, but had the knock. I...
See more
Top