Recent content by c_douce

  1. c_douce

    2 Cylinder Johnson 40hp Old Trim/Tilt

    Hi, were can I purchase the old cylinders for my Johnson 40hp trim or rebuild them?
  2. c_douce

    2 Cylinder Johnson 40hp Old Trim/Tilt

  3. c_douce

    2 Cylinder Johnson 40hp Old Trim/Tilt

    Revised, "R", thanks for the info, yes, I do know the trim is on the motor side, the other is the tilt, but I'm asking for more details of my ?'s, so I don't screw up anything, I will be filling the other cylinder today just to see if anything is leaking or is it dead.
  4. c_douce

    2 Cylinder Johnson 40hp Old Trim/Tilt

    Hi, Purchased the old trim, the cylinder attached to the motor trims up, the opposite cylinder has no pressure, just slides, opened the, I would guess the refill valve that has a wire attached, no fluid inside, possible leaked out, if I refill, would It hold and due to that side not working, why...
  5. c_douce

    Johnson 1986 40hp Power Trim & Tilt

    That link sent only goes to more links and more links and more links. gave up and called my local guys, found a match.
  6. c_douce

    Johnson 1986 40hp Power Trim & Tilt

    86 Johnson 40 hp outboard. J40elcde. This model is hard to find a power trim & tilt. Can I get some info where to purchase new or used in Ontario, Canada?
  7. c_douce

    Runabout hull plug?

    Is there a plug or screw for the hull? I noticed a hole accross from the drian plug in the rear of my boat and water coming out from this baby finger hole.
  8. c_douce

    1962 EVINRUDE CARB QUESTION FROM THREAD YESTERDAY 08:53 hrs

    Perfect Lindy46 from your reply, you where right about the float, it was in a really bad condition and replaced the float with a new one! cleaned entire carb and changed all gaskets, overhauling completed. So the adjustment knob on the right controls the bottom high speed correct? I have a...
  9. c_douce

    Evinrude Model 282526 Electric Start 1962 Or 196?

    Attempting to find the correct parts in iboats catalog, Im not finding the exact match, there are could be's, but can you please elaborate why or can you give me all the info you have, it would be nice to know, since I was informed that it's a 1964.
  10. c_douce

    1964 Evinrude 28 hp

    Wont start, I rebuild the carb and since, it will not turn over?
  11. c_douce

    1962 Evinrude Carb Gas Flow

    Hi to all, my 1962 28 hp evinrude elec shift has gas pooring out of the bottom of the carb, I did not prime it, I just connected the hose and a few minutes later I smelled gas, I removed the cover, checked and I could see gas flowing out the carb, do I need to service the carb?
  12. c_douce

    Evinrude 1966 water flow

    The water flow is spitting out of my 1966 motor, should it be a steady flow or is this normal.
  13. c_douce

    Evinrude 40HP on a CMC PT35 Power Tilt & Trim

    Hi to all, can I cause any damage if I put my 40hp on a CMC PT35, I know it's rated at 35, but just asking?
  14. c_douce

    Johnson power tilt & trim on a Evinrude

    Hi to all, can I install a Johnson mid 80's power tilt on a Evinrude 40hp 1966 elec start?
  15. c_douce

    1964 evnirude speeditwin ski-twin elect start will not start

    Hi to all, I had my 1966 evinrude 40 hp elect start hooked up and ran great (control box in the back of my runabout), but when I hooked up my ski-twin it would not start, I checked the box connections and no power was going to the motor, but the other motor had power to it and ran, I jumped, and...
See more
Top