Recent content by Cameron119

  1. C

    Evinrude 90HP won’t go over 2000RPM

    So I had a guy diagnose it today and he said the two coils on the right side of the motor were cracked. That explains why the right side of the motor was cool to the touch and only the left side was hot. This also limited the RPM to 2000. So after I replace the two coils I will report back and...
  2. C

    Evinrude 90HP won’t go over 2000RPM

    I’ll look into the cost of one today thanks again racer.
  3. C

    Evinrude 90HP won’t go over 2000RPM

    Yes I will post I have a marine mechanic gonna take a look at it for me next Wednesday. I’ll post his findings.
  4. C

    Evinrude 90HP won’t go over 2000RPM

    Hey guys just a thought I didn’t have time to do all that troubleshooting you guys suggested yet, but I remember just before it happend I asked my daughter to put the boat into neutral from a slow forward and I think she did it without depressing the red grip switch on the shifter. Could that in...
  5. C

    Evinrude 90HP won’t go over 2000RPM

    I will try the impeller. From what I remember I will need to drop the lower unit for this.
  6. C

    Evinrude 90HP won’t go over 2000RPM

    Ok perfect this is one thing I will take a look at when I get back home. Does anyone know where I can download a copy of the service maintenance manual for this motor?
  7. C

    Evinrude 90HP won’t go over 2000RPM

    So it was on the driver side (port) where there is only one wire(tan) and that side was nearly scalding to the touch while the other side was just warm. I’m not worried about the spark plug gaps because the engine was running perfect for days then suddenly stuck at 2000rpm. I find it hard to...
  8. C

    Evinrude 90HP won’t go over 2000RPM

    Roughly 3/8” gap. I did not use a spark tester we pulled the plug and re attached the wire with it grounded on the power head to test spark.
  9. C

    Evinrude 90HP won’t go over 2000RPM

    When I pulled the plugs they were only slightly discoloured and had a very light brown coating, not hard carbon. We tested all 4 plugs one at a time and looked for spark and it looked good, the plug gap seemed quite wide, I’d say around 3/8. As far as compression I won’t be able to check until...
  10. C

    Evinrude 90HP won’t go over 2000RPM

    Evening everyone. Short back story. Had my 90 evinrude (E90eleuc) serviced last year was purring like a kitten. We were out tubing and all of a sudden after going in neutral to switch riders we can only go 2000rpm. I noticed one of the sides of the engine feels very hot to the touch, the other...
  11. C

    E90ELEUC Starter housing blew apart? Not sure what happend. Please assist!

    I never personally lubricated it in the 5 years I’ve owned the motor. Was not aware this had to be done. Thanks racer.
  12. C

    E90ELEUC Starter housing blew apart? Not sure what happend. Please assist!

    Hello there ladies and gents I have an E90ELEUC and was winterizing it by flooding the carbs with stabilized gas. During this process of starting the engine I heard a bang and then looked back and it’s almost as if the head of the starter blew through the plastic shroud on top. Is this an easy...
  13. C

    E10RNCS running/starting issues

    Good morning. Here we go again with my beloved 9.9 that I just cant seem to get purring like a kitten. I just finished rebuilding the lower unit by replacing the seals and gaskets to prevent water from leaking into the oil in the gearbox ( This went well ). I put the motor back together and...
  14. C

    E10RCNS 9.9 1982 evinrude lower unit seal kit

    Nice to see your still around racerone. It’s been years since I’ve posted here. Yes I will reach out to my local evinrude dealer about this to make sure I get the correct kit.
  15. C

    E10RCNS 9.9 1982 evinrude lower unit seal kit

    Good morning. Looking to purchase a lower unit seal kit for my engine model listed above. Want to make sure I order the correct one. When I google the engine type this is what comes up. Will this work? Sierra #18-2684 Lower Unit Seal Kit Any help is appreciated. Thanks
Top