Recent content by cbcmarine

  1. C

    Raw water pump 2000 Volvo pent 4.3 GL

    Ok I have a leak and see the seal is shot so I have ordered from England and should be here in a week I have also ordered a new bearing My question is this I see no retaining ring for the bearing it is just pressed flush According to all the Diagrams I have seen for Johnson pumps this is not...
  2. C

    1978 Merc 90 Timing issue

    So I had to replace the trigger, that did not go so bad as I thought, got it all back together and I have spark and have adjusted the timing as per the merc manual. The single dot lines up with the arrow. It will fire but not run ?? I tried moving it back counterclockwise as manual states ...
  3. C

    1981 150 evinrude starter mounts ripped out

    Hi all so on my 150 workhorse the starter became loose and the starter bolts ripped out and cracked two of the mounts. I am taking apart to go into to a machine shop and try to weld back together. If this fails will the bottom end of another 150 just bolt right on? are these parts matched ...
  4. C

    1988 Merc 8hp

    I have a 8 hp merc that won't go into reverse. I have taken apart the bottom end and the gears seem fine there was lot's of water when I drained for the fall so I was going to replace the water pump and seals as well as the seal in the gear case housing anyway. I don't have alot of experience...
  5. C

    1982 150 Evinrude Starter mounts broken off

    Hi All so my 1982 Evinrude that I just did the power head on Last year has had the mounts broken off. Is this a right off or can a good welder for Cast work some magic ? Is it worth it ? Thanks
  6. C

    Picture's needed

    Hi I am trying to convert a tiller handle from a 1993 9.9 HP to a 1992. So I need pictures of the cable routing from the tiller handle to the connection point on carb off a 1993 Johnson/Evinrude 9.9 a 1994 or 1995 will also work Thanks Shaun
  7. C

    Convert tiller from a 1993 to 1991

    Can I use the tiller Handle from a 1993 Evinrude to a 1991 Evinrude 1991 both are 9.9. I know they are different has anyone ever done this conversion ?? ideas ? There are not great pictures of the hook up for this
  8. C

    1991 Tiller handle What years will work

    Ok so I need some helps what year tiller handles will work for my 1991 Evinrude 9.9 hp Model is CE10REIR Any help would be appreciated Shaun
  9. C

    1991 Evinrude 9.9 missing tiller handles

    Hi all so I have two motors the same that the last owner converted to remote control. I am looking to convert back does anyone have a parts break down for these motors so that I can find what I need.
  10. C

    What year is my 9.9 Evinrude

    Hey all I know there is probably a site for this ? Model CE10REIR Serial # 9 02982217
  11. C

    81 Evinrude 150 Bottom End Pinion nut

    So I have everything apart what size is the Pinion nut wrench that goes in the Gearcase ? Also socket 311875 only from OMC ? or does someone else carry it ? Thanks
  12. C

    1981 150 Evinrude Blown ?

    So all I have a question I had one of my boats on loan and they brought it back possibly ceased. The flywheel will not turn I have checked plugs and they look fine so I am just about to pull the head. I did just rebuild this motor a year and a half ago with a new top end. SO my question is if...
  13. C

    1978 Merc 90hp Starter issues

    So I started old faithfull up and sounded like metal on metal !! Thought cylinder however under more investigation seems as thought the starter teeth are a little eaten up and it does not always catch the flywheel the greatest. My question do you normally have to shim these starters, I never...
  14. C

    Power Trim 70 hp

    So I have an 1988 Merc 70 and the trim motor seems to be gone. I test to ground and it is showing a circuit. Any one know the usual culprit and are they hard to rebuild. It is first start up of the season so I thought it may have been stalled but not so lucky. One more thing my Serial numer...
  15. C

    Lower unit done

    Hey all was crusing along and noticed odd bubbles ahead of me slowed down quick to discover divers !! (NO DIVE FLAG) turned quick and got more concearned about hitting the diver rather than the rocks that I have known about my whole life !!! Any way took out the prop and the skag there is know a...
See more
Top