Recent content by CH1968

  1. C

    Torque for Flywheel Nut - 1989 Johnson 110HP 2T

    the manual refers to 'table 2' for flywheel nut specs. i cannot locate this table 2 in the manual and kindly ask what the torque spec should be for the flywheel nut?? cameron
  2. C

    Confirmation of Holes in Water Cavity - Johnson 1989 110 2T

    I need to be in contact with someone who knows this particular block and what specific holes should be inside this water cavity - especially those 2 holes highlighted in this picture. Any contacts/links you can provide me would be great. And, what type of welding needs to be used on this...
  3. C

    Bendix Gear Not Rising to Engage FLywheel (Johnson 1989 110HP 2T)

    I try to start, and I see / hear the bendix gear spinning, but does not rise to engage the flywheel. Next steps in troubleshooting this one? Byte
  4. C

    Alarm - Johnson 1989 115HP 2T (Help Needed)

    All, Just started my outboard (with ear muffs over water pump area) the first time in 18 months - after an extensive storage period of non-usage. It ran fine (idle only) up to 3 minutes - then an alarm sounded at the console and i turned it off. I do not know if this alarm was caused by...
  5. C

    Starter Motor Will Only Half Engage

    Team, Why does the spindle gear on top of my starter motor only half engage the flywheel? Please help. Johnson 110HP 2 stroke 1989.
  6. C

    Correct Prop for Johnson 110HP

    " http://www.dixiemarinesales.com/detail.aspx?ID=409" Hi Team. I had this prop (13 7/8" dia x 17" pitch) put on my motor recently - Johnson 110HP 1989 2-stroke. It's WOT operating range is 4500-5500 RPM - as per manual. I do not have a tacho so I do not know what WOT I am actually pulling...
  7. C

    Changing Powerheads

    Hi Team. Donk 1: A-J110TXCEM 25" leg Johnson 110P 2-stroke 1989. Donk 2: B- J115TLERC 19" leg Johnson 115HP 2-stroke 1994. I currently have donk 1 on my boat and thinking of buying donk 2 for this same boat (transom 25") because I think my donk is stfd. AS you see, I am unable to simply...
  8. C

    Cleaning and tuning Carby for 110HP Johnson

    Hi Team. I have a rich mixture because my plugs are always wet and starting is always an issue. Can you all inform me what I need to do to ensure I run the right mixture so that my plugs do not wet up and I can start ok. 1989 110HP Johnson 2 stroke VRO Cameron
  9. C

    Height Location of Prop Relative to Bottom Of Transom

    Hi Team. I have the 25" shaft on my 110HP Johnson on a 25" transom - all good. Where (vertical difference in height) should the prop shaft sit in relation to bottom of transom? Optimal location to eliminate caviation, etc. Cam
  10. C

    Looper Johnson Outboards

    Hi team. I have been asked if my 1989 110HP 2-stroke is a looper. It's model number is A-J110TXCEM. I aslo want to know if another donk I am intereested in (1994 115HP BJ115TLERC) is a looper. A looper is apparently better. What is a looper? How do I tell if I have a looper? I have been...
  11. C

    psi for 1989 110HP Johnson 2 stroke?

    Hi Team. What is the factory psi for this model donk? What is an acceptable psi for this model donk still running today? Where can I find these readings? Cameron
  12. C

    Schematics for 1989 OMC 110HP

    Hi Team. Can someone please provide shcematics of the carbies and head for the folllwing donk model number : A-J110TXCEM 25" extra long shaft. Also, what year and specs have the following model number: BJ115TLERC? Cameron
  13. C

    1989 Johnson 110HP - teething issues

    Hi Team. My very first post and I dearly hope you can assist me with my 1989 110HP JOHNSON 2 stroke VRO outboard. I have spent countless hours on this baby and don't want to give her up. Issue 1 - Overheating alarm comes on at close to WOT (4500-5000) RPM. Issue 2 - I need to lift leg...
See more
Top