Recent content by cor21e

  1. C

    Yamaha 2006 f150 is ratcheting/ grinding in forward only

    I have a Yamaha f150 2006. 220hrs. Just installed it. When I am on the water, And shift to forward, it is grinding. I took the shifter cable off and was shifting the engine with my fingers. It was very easy to push it toward the stern and into reverse. When I tried to pull it into forward...
  2. C

    Yamaha 2006 f150 lower unit convert from 25" to 20"

    I just got a great deal on a 2006 f150 with a 25 inch lower. I need to know how difficult it is to change it over to 20 inch and remove the spacer block I know I need a new Drive shaft, shift shaft, and water tube, and trim anode bolt. I have heard that people regularly do this to their...
  3. C

    command link wiring question- two tachs?

    I am trying to hook up two tachs to my tower boat. will this work?
  4. C

    command link gauge tightening nut missing???

    I have a command link tach gauge. There is a huge nut that spins over the entire back. it is used to tighten the gauge to the console. I cannot find it. Does anybody know where i can find a part number? thanks in advance iboats community
  5. C

    honda 25 convert to 30

    How do I convert a 2005 honda 25 to a 30. They are the same engines. I just want more power. THanks.
  6. C

    etec 25 selling price

    I just aquired an etec 25 2009 and am wishing to sell it to get a bigger motor. It has 4 hours and 12 minutes of run time on it. It is manual start and trim, 15" shaft and is immaculate with over a year left on the warranty. How much is my motor worth? Thanks in advance guys
  7. C

    going nuts with '72 25 evinrude!!

    Ok so I have almost taken this entire engine apart and put it back together ( learned alot) so I put it out on the lake and it started up great ( just rebuilt the electrical starting system ). I just put a new impeller in and a new thermostat I still need to redo all the seals in the lower...
  8. C

    replacing 1972 evinrude lower unit seals

    I continue to get water in my lower unit. So I think I have decided to buy the kit to replace all the seals. I am a little scared of attempting this project but am determined to do it. I have been searching this site but cannot find a good post with pictures and lots of details including what...
  9. C

    Have parts from 72 25hp evinrude

    I have some parts from my 72 evinrude 25hp. I was wondering if anyone needed these for their project. I am going to put these on ebay but if anyone would need them on this forum just contact me 1 is the electric choke and other parts to it 2 is the original wiring harness for the electric...
  10. C

    dumb starter ?s. 25 '72 evinrude

    Why do I need a solenoid to start the engine? Why don't you just use a direct connect to the starter with the positive side having a momentary switch on it?
  11. C

    evinrude 1972 25hp help !

    I tried to pull the lower unit off to check my impeller and got the shift link undone and free and the lower unit would still not slide off. Then I forced it down and the lower unit came off. The only problem is that the drive shaft is still in the engine. Did I screw up bad? Why did this...
  12. C

    1972 evinrude 25

    I just aquired an evinrude 1972 25hp for $200. I am currently going thru it and taking almost everything apart and cleaning and reasembling. I have a couple questions so far. ( I have read a hundred old posts so far. THere is great info on this site) 1. How do I remove the lower unit? Is there...
See more
Top