Current visitors

Home
Members

ct1762@gmail.com's latest activity

ct1762@gmail.com replied to the thread 1998 evinrude 225 ocean pro help #2!.

yes a simple 10w 10 ohm resistor is easy and dirt cheap to find on amazon. they are used for headlights on mopeds and such. test primary...

Friday at 1:01 AM
ct1762@gmail.com replied to the thread Just adopted..1968 Evinrude Outboard 85 HP Parts Catalog Manual 85852A 85853A Speedifour OEM.

i have quite a few parts for these when i acquired an old dealers stock. complete water pump kits too

Mar 30, 2025
ct1762@gmail.com replied to the thread Evinrude 70Hp bogging in the water.

only way to know is to make 110% sure delicate idle circuits in all carbs are clean, and firing on all 3 with good compression, and...

Mar 30, 2025
ct1762@gmail.com replied to the thread Ruh-Roh… a new gear case may be in order.

i remember now! had a customer with same motor and i did the same thing:)

Mar 25, 2025
ct1762@gmail.com replied to the thread Ruh-Roh… a new gear case may be in order.

i dont think the dowels are of particular concern, but the shimming sure would be. thats something that must be done. you could get...

Mar 24, 2025
ct1762@gmail.com replied to the thread Black scuff marks on cylinder walls.

yes but im just saying while its apart cant hurt to get a jump on it. we all know how quickly carbon can build on these!

Mar 24, 2025
ct1762@gmail.com replied to the thread Black scuff marks on cylinder walls.

yep. for a couple hrs then run the motor. to get everything off i use grease to seal the rings off and a soft wire wheel to get all...

Mar 23, 2025
ct1762@gmail.com replied to the thread Black scuff marks on cylinder walls.

they look very good to me. id get those pistons soaked in engine tuner or power tune while the heads are off to remove all carbon until...

Mar 23, 2025
ct1762@gmail.com replied to the thread Ruh-Roh… a new gear case may be in order.

looks like the parts motor you have MIGHT work as its a fine spline (last year of older style trim pretty interesting). as you said swap...

Mar 23, 2025
ct1762@gmail.com replied to the thread Ruh-Roh… a new gear case may be in order.

i believe the etec 40-60hp motors used the same gearcase as a 50-70hp 3 cyl 1989-up but not sure if the driveshaft is the same. just...

Mar 21, 2025
ct1762@gmail.com replied to the thread 1998 evinrude 225 ocean pro help #2!.

well the flywheel should always be spinning clockwise no guessing needed! if the gearcase is a counter-rotating one you'd see a "CR"...

Mar 21, 2025
ct1762@gmail.com replied to the thread 1998 evinrude 225 ocean pro help #2!.

are you sure the rubber grommet is in the pump for water tube? the o ring is behind the plate AND underneath the impeller? keyway is in...

Mar 18, 2025
ct1762@gmail.com replied to the thread Golden Jubilee Evi Sportwin 10 - Should I convert?.

i have a good supply of the red Sierra Magnatune or ATOM ignition modules. you can use green as well. seem to be the same. they do have...

Mar 18, 2025
ct1762@gmail.com replied to the thread FICHT ...code 38.

sounds like good advice. the pump is $25 or so on ebay usually unless there is something expensive about this one. yea the list price is...

Mar 18, 2025
ct1762@gmail.com reacted to padraicbc's post in the thread Removing tilt and trim unit from 2004 johnson 90hp with Like.

Thank you. I guess the 2 ton hoist I bought will finally have a use!

Mar 18, 2025

Show older items

Home
Members

Top