Recent content by eula30

  1. E

    Johnson 25hp won't start

    Hi there I have a Johnson Model: 25R76E and Serial Number: E4431642, any idea of the Year, Horse Power and what type of sparkplugs should I used.<br />I will really appreciate any Help.<br />Thank you
  2. E

    1994 Evirude 200hp RPM to High

    Hi there, I have an 1994 evinrude 200hp, with ear muff I get 2000 rpm at idle, and when I got to the boat ramp I get 1000 rpm and it idles really good and will never go off, but If I bring the rpm down with the ear muff to a 1000 rpm at idle, when I go to the ramp I get below 200 rpm at idle and...
  3. E

    Evinrude 200hp voltage????

    Hi there, in a 1994 evinrude 200hp. Any idea what’s the Voltage from the power pack to the coil? (I got in DC 2.6V) and from the coil to the spark plugs? I got in DC 2.6V), I'm trying to find out if the coils are bad or the power pack. Motor was running fine until yesterday, didn't start, I...
  4. E

    1994 200hp Evinrude propeller

    I have a 1988 aquasport 222 CC with a 1994 200hp evinrude, the propeller on this motor is 14 1/4 X 19, boat runs 48mhp at 5000 rpm, I also have an extra 14 1/4 X 21, if I replace the propeller with the 21p, my rpm will be higher or lower than 5000 RPM? I think I will gain more speed but how...
  5. E

    1993 Johnson Sailmaster 9.9hp Battery Cables

    Hi, I have a 1993 Electric Start Johnson Sail Master 9.9Hp. Model: J10SELETM, Any Idea where the Battery cables go to? I can see the red wire connected to the starter and to the rectifier, I also see the black Ground wire, I can see all 3 wires until they get to under the carburetor there, it...
  6. E

    1994 200hp Evinrude?????

    Hi, I have a 1994 200hp Evinrude that came with a bad trim motor, I did install a new motor Today, and fill the up with trim fluid, I try to tilt the motor and it will not go up, I can heard the trim motor running, but motor will come up a little bit and that's about it, I check for fluid and...
  7. E

    evinrude 6hp ????

    Hi there, I have an Evinrude 6hp. Model: E6RET8, color: blue. Any idea on what year this is? Also, motor has the Lower Oil plug thread is stripped any way that can be fix or I will have to buy another lower unit?<br /><br />I will really appreciate any help of you part.<br />Thank you
  8. E

    OMC Sea Drive

    I have an OMC Sea Drive <br />Model: 1AALCNF <br />Serial# J735818<br /><br />Any help with year and HP? <br />I will really appreciated <br />thank you
  9. E

    Evinrude HP and Year????

    Hi there, I have 2 Evinrude outboard motors, don't know the year and HP. here are the numbers on the motors: <br /><br />1st: Model: 15504C<br /> Serial# E0004051<br /><br />2nd: Model: 10824M<br /> Serial# E0002518<br /><br />I will really appreciate any help.<br />Thank you
  10. E

    1997 Mariner 4-stokes

    Hi there, any one know how to drain the oil on a 1997 4-strokes Mariner 50hp outboard, model: 50ELPT. I will really appreciate any help.<br />Thank you
  11. E

    1995 mercury compression test

    Hi there, I just received 1995 Mercury 150hp 2.0 Liter, I did a compression test. From left side first and top to bottom:<br /><br />1) 115<br />2) 116<br />3) 0<br />4) 116<br />5) 115<br />6) 115<br /><br />piston number 3 there is no compression at all, you see the piston moving back and...
  12. E

    1976 evinrude 9.9

    Hi, any idea on how can I remove these bolts; I remove the lower unit to change the impeller and broke about 6 of them. I will really appreciate any help.<br />Thank you<br /><br /> <center><br /><img src=http://img.photobucket.com/albums/v11/sportcraft17/Image607.jpg><br /><br /><br /></center>
  13. E

    1976 Johnson 200hp Tach ( RPM) Help!!!!!!!!!

    Hi there, there is no wire coming from control or motor to the tach, the wire I found Gray red and black wore cut, I have dismantle the control so you can see the cables inside I also took some pictures of the 2 tach that I’m using, is there any way to send a cable from the motor to the tach, I...
  14. E

    Johnson 200hp Proppeller

    Hi , I have an 1976 200hp Johnson with a 1976 21 footer Grady-Whites WA, The propeller on the motor is a Aluminum 15 1/2 X 19 I'm doing 45 knots with full load very happy with. I just bough a Stainless Steal Power tech 15 ¼ X 17 any Idea with one should be better…<br />Thank you
  15. E

    1976 200hp Johnson

    Hi there, any ideas on why this motor 1976 200hp Johnson is leaking oil thru the mid section, every time I start up the Motor oil will come out thru the outside top part of the midsection, even if I run the motor for 2 minutes oil will come out. Is that because I have a faulty gasket between the...
See more
Top