Re: rollers or bunks which carries the weight
Just to add to the fray. I just had my 10,000lb trailer's axles replaced after 15 years of excellent service. I asked the manufacturer to replace the yellow stoltz roller which had badly rusted shafts. He indicated that they no longer use the...
I didn't want to jack the "Idiocracy at the launch" thread but I had a question to offer to the group.
WSDavis posting exactly mimics our ramp setup. Four launch lanes on two docks. (1x23x4). There is a wide road on the right side for the approach and prep while leaving on the left side to...
Planning on adding a dive ladder to my boat. The best place for the bracket is on the starboard side right where the HIN is located. Is it a bad idea to bolt the bracket over the numbers. And a step further, at least one bolt hole will go through and deface some of the digits. I live in Florida...
Voltage regulator died. Troubleshot with ac multimeter at two yellow wires at about 1500 rpm - puts out 32 volts.
So I ordered a OEM 0585219 RECTIFIER & REGULATOR
What came was a 0439561 which is evidently the replacement part. My problem is the existing regulator has two yellow, one grey...
2000 ox66 -- Finally cleaning the water passages to remove scale. anyone happen to know the torque specs for the heads and water covers for re-assembly?
Many thanks!
My buddies engine is overheating. We replaced the thermostats and PRV. He claims the impeller was replaced a few months ago. New stats helped but motor still overheats at about 3800 rpm consistently. Pees a good stream, stream is cool while alarm sounds can hold my hand for two seconds on head...
I live in SW Florida and my AC is running continuously and will not maintain temperature. Looking for suggestions.
Here is what I have - American Standard 4 ton 15 SEER split system about 4 years old.
My house is 2100sqft under air 3BR 2 bath CBS construction built in 85 with a bunch of blown...
A little bit out of my comfort zone here so be gentile :)
My friend has a 77 Ski Natique with a ford 351 Windsor that runs backwards - counter rotating. I am helping him re-build the bottom end. He ran it low on oil and it developed a rod knock.
To make a long story short it seems the main...
J150EXEOM 1995 - How difficult is it to replace the gear case seals? Is total dis-assembly required? Reading my factory manual makes it look like a tough job with lots of specialized tools.
For a competent persons first time in the gear case is this big job?
Free Download:
987c SI Combo Update (version 4.770 - 0 bytes)
Description:
And it's free!!!!
1/14/2010 12:00:00 AM - v4.770 Adds Down Imaging. Adds LakeMaster compatibility. Adds GPS improvements. Adds new 2D sonar color palettes. Adds New SI sonar color palettes. Improves trolling motor noise...
Reading an article on the Johnson repair board about Wyraps made me remember this tip, and I thought I would share.
When you cut a Tywrap with wire cutters or diagonal cutters (dikes) if you cut the Tywrap by the edge it will not cut you open and make you bleed like it does if you cut it on...
I personally am celebrating the end of 09'. What a year...
I suggest that instead of slowly dropping the 2010 ball in the gardens they throw off the old 09' ball and let it smash on the sidewalks.
What do you think?
My 1995 150"s had a wax like light amber coating sprayed on them. I dont know if the previous owner did it or the dealer (one owner boat).
Anyone have any idea what the heck this stuff was. I rebuilt the engine and would like to re-coat it. The original stuff worked well, neither engine has...
Power Grab is rapidly becoming one of my favorites. Anyone ever use this stuff? I've used it to hold cable modems, routers, brick power supplies, outlet strips etc to the undersides of cabinets and other places where your installing something that you want to stay put but in 5 years you'll be...
