When I start the motor it idles fine about 900 rpms when I try to put it in gear it dies. I have tried to idle it up but there is no more room to the screw. I have heard about link and synk but don't know if that applies to my motor.
The screw I mentioned is on the arm that moves the stator...
Ok I have rebuilt the carbs and replaced all the fuel lines. I have a new line to connect to the fuel tank and a new tank ( 5 gallon portable) and new fuel mixed 50:1.
When I try to start when cold I have to spray fuel into the carbs to get it to start. Then when I stop on the lake for any...
I have a 1993 Ford Crown Vic 4.6L V8. I started it up today and it wont idle. It revs up to normal idle and then almost dies then back up to normal idle. It will keep doing this until I put it in gear then it will idle fine. It does this hot or cold. <br /><br />I have removed the Idle Control...
I have a 1976 115hp Johnson on a 17ft Sunbird.<br />It takes forever to get on a plain. It like I just have no take off power. During take off I am at WOT and I have about 3000 RPM it eventually<br />get on a plain and tops out at 4900 RPM. I have tried 3 diffrent props a 16, 19, 21 pitch I get...
The motor will not stay up. When i'm on the lake it will not trim up while I am moveing its like it doesn't have enough lifting power. When I stop it lifts fine but when I lower the motor it struggles and moves real slow. Ihave rebuilt both of the pistons. <br /><br />Do I need to look into the...
Hello <br /><br /> I am trying to hook up this tach to my 1976 115hp johnson outboard. The tach has a sticker that says it works for 5/6 pul/rev alternator equiped outboard. The sticker also has a number on it 174887. <br /><br />I need instructions on how to hook this up. [/IMG]<br /><br...
I am rebuilding a 1976 115 hp johnson carburetor. In the manuel it says the float drop should be 7/8-1 1/8 in. Does this mean that anywhere in this range is ok or one need to be 7/8 and one needs to be 1 1/8?<br /><br />Thanks for all the help.
Do I need to compress these core plugs or is it ok to just push them in. <br /><br />They are just pushed into place in the picture.<br /><br />Carburetor is off a johnson 115 1976.
I have a 1976 Evenrude 115hp 4 cyl outboard. I want to get a tachometer for his motor but I dont know what will work with this motor.<br /><br />Is there a specific type or brand or do I look for the type of hook up it uses?<br /><br />What do I look for and what type of hook up do I need?<br...
I am rebuilding the Carburetors on a 1976 johnson 115. I am wondering if any body has a guide or just some advise as what to look for and what I need to make sure gets clean and if there are any adjustments that I need to make. <br /><br />I am useing Iboats 18-7046 carburetor kit. It has no...
I am looking for the nylon spacer(connecting rods piviot on these) on the carburetor for a 1976 115 hp Johnson. I can't find it on IBoats. If anybody has a part # it will help.<br /><br />Thanks for the help.<br />
I am looking controls for a older johnson 40hp. When I say controls I mean the starter switch it has a old style connector that I have never seen. I am not just looking for a switch but the interface with the motor. It is not the round plug it is square. I will update this fourm as soon as I can...
Hello all and thanks in advance for you help.<br /><br />I have a 115hp johnson 1976 on a 17ft sunbird.<br />This motor takes forever to get on a plane and just seams to have no power what so ever. Here is a list of this I have already checked.<br /><br />Carbs- Just rebuilt<br />Fuel- New bulb...
I am looking to install a tach on my 1976 115 johnson. I have looked online and i don't know wich one to get. I hope you can help me with this and maybe some websites to order from.<br /><br />Thank guys
