can anybody tell were this spring goes on a 9.8 110 mercury, it was looped on the end like it would go around a bolt, but it straighten out when i pulled it to a bolt in its path, but the bolt was to far away. i know it goes around the half moon plastic peice but i dont' know what it attaches...
i tore the motor down last year to replace the plastic peice for the shifter now i have time to put it back together i could use a diagram so i dont put something on and have to take it back apart because i missed something any help would be appreciated thanks
my brotherinlaw found a great deal saturday morning at a yard sale he bought a 9.8 merc that had been sitting in a guys garage for years he was told the motor ran when it was put away he only paid $25 i have not had a chance to start it for him yet i lubed every thing and i have spark just going...
i was just wondering who has a 1984 evinrude v4 90hp and if you like the engine right now mine is sitting on the stand it starts up nice and shifts good a friend gave it to me but before i put it on my boat i just want some opinions on the motor i was offered a trade for a 50 hp evinrude...
from the picture can any one tell me how this piece hooks up to the motor runs great but when i release the tiller handle it goes back too far and quits my brother in law gave me the motor because it would not run right i bought a armature bearing today and put it on now it starts second pull...
my brother inlaw gave me this motor he used it on a zodiac he said it was getting to hard to start so he bought a newer motor first thing i noticed when i put it on the stand and tried to start the motor was it was hard pulling over even with the plugs out so i thought maybe something was tight...
good morning you have a envinrude v4 engine maybe you could answer my question i had just put on a thread with pictures were does the water come out of a 1985 v4 evinrude 90 hp if you check out that thread maybe you could help thanks
when i put the earmuffs on the engine and start it the water comes out of the two lower holes on the front side of the bottom end in the first picture no water comes out of the two holes back side of the bottom end at the top just exuast in the second picture is that right o by the way when i...
okay maybe im going at this wrong i only let my 1984 v4 90 hp evinrude motor run for about 20 to 30 seconds then i shut the motor down because i don't see any water coming out the pee holes. on my motor the water comes through the heads into the thermostat housing then to the pee holes can any...
i finally have water coming to the heads but no further the water comes from the heads but does not come from there to the pee holes is the block below the two hoses that come from the head the thermostat housing also i have a black button when i first start the engine i have to hold to get...
i have oil leaking around the propeller shaft i took the 2 screws out that hold the peice that holds the bearing and seal and oil ring not sure the name of the peice but i noticed the oil seal is bad can any one tell me how i get the old oil seal out can i remove the bearing to get at it if so...
my manuale only goes to 1982 it says measure from the top of the bottom end to the centre of the hole on the shift rod at 21.844 inches which i assume is about 21 7/8 roughly but it does not say if in forward, reverse or neutral but neutral would make sense to me does any body know if the 1984...
i need to change the back to back seals on my 1984 90 hp v4 evinrude outboard the ones behind the prop i took the 3 bolts out now can anybody tell me if i just use a puller to pull the rest or is there a trick to it thanks
i tried my bottom end in the barrel and finally have it pumping water now i need to replace the back to back seals behind the prop when i got the motor there was oil leaking from the seals but when i checked the oil it was good and now when i checked the lower unit oil it is milky can i just pry...
