Needs some help I have a 2001 225 optimax That will not go over 2000 rpms
The story on this motor it always ran great till one day I was fouling number 6 cylinder plug over and over turned out to be a bad air injector so I replaced it thinking it was the main problem. Well that wasn’t the case...
Can anyone tell me y my 2001 optimax Is fouling out one plug .
The plug is black very black and dry as a bone. What I have done so far. New plugs wires fuel filter injectors where sent out to be cleaned and tested.new tracker valve. Motor starts very easy runs great for one outting no lose in...
Long story short. I have a 1993 xri 2.5 200hp
that has a bad cylinder head from piston ring damage
but I have a cylinder head from another powerhead that is a 1990 2.5 200 non xri with a different casting number
if you put them side by side there is not much of a difference. Is this do able or...
Hey everyone Just wanted to post my new project.
This is a thunderbolt bass boat I found in a junkyard. I completely rebuilt this boat ,New wiring ,Deck, Pumps, Bodywork and paint , Seats, and the list is long but we are getting there..The only real problem I had was getting a title for it.Pa is...
Ok Ill start with I got a motor for cheap. When I got the motor the guy told me it ran but the last time he had it out it overheated on him on his way back to the dock .He let me know that he shut it down and trolled back and didnt run the motor. Ok so now I get the motor from him but he at one...
,ok guys this is what i have going on last year she ran great but started to have problem at the end of the season.
Cold start real pain but i know they where from the get go but when warm she started with no problem ok so this was my problem last year try to get up on plane she would die and...
Ok guys and girl Im lost with a new boat hull I just got super cheap
Im going to restore her for my son But I have run into a problem
I can find any info on the boat I have never seen one on any lake in my area.
This is what I do know its made by klassic boats no longer around
It has a plate...
Ok guys Im new to the inboard motors so I have a ?
Ok a friend just gave me a boat with a 188hp meruiser engine well it did run but that was ten years ago and well you know the story.Any how I would like to replace the engine and I have a nice ford 5.O will this bolt up and if not what ford...
Hey guys I have some ?
I just got a free 120 force I dont know what year it is Ser e075793 I did the search (nothing) I would say its a 92
Ok now onto testing it
I tried to turn it over no good I think its froze
I have the plugs out and spray PB into each Cyl and let it set for a day
Now...
Hey guys can someone tell me if I lose the ground on my force rectifier will I lose power in wot.The other day I had my boat out and it started to lose power and would stall out but would start back up no problem.Now when not WOT it would run just fine. I got back home and I was looking around...
Guys I have it all apart and I can see someone before me did to.
I think im missing parts.
I have four B/B three large and one small
I have two springs one large and one small
Now the info I have is telling me I need 3 springs two large one small
and three B/B Two larg and one small...
Hey guys got a new problem with my tilt trim unit.
1. Slow leak down
2. manuel release will not work ,If I remove the bolt shouldnt I be able to move the motor up or down.
3.Can I rebuild the trim pump valve body myself and what parts would I need and part numbers.
Thank Shawn
ok guys I have this fish finder and it has a bad transducer.
The problem is the transducer is XHS-6-24 beam and I would like a smaller beam is there a different transducer I can use with this unit .I know this is a long shot:D
Thanks
