Recent content by GetReel

  1. G

    Primer Bulb ? 200 HPDI

    Primer bulb won't pump up tight on 2006 200hpdi the same bulb pumped up tight on the old 200 johnny,put new one on same thing ? engine runs fine but not sure about the primer bulb not pumping up tight. Thanks for any info Ol 23 mako
  2. G

    200 HPDI rpm ?

    New 2006 HPDI 200, 15 3/4 x 17 prop, on a 23' mako. Ran the required break in time, tried full throttle just for a few seconds but would not go over 5000 rpms, with a inch of throttle left after it hit 5. Could there be a code set on it? The motor does have less than 10 hrs on it. thanks for info
  3. G

    Rodbolt...first start up !

    2006 200 HPDI.. everthing is hooked up but fuel line .multifunction tach etc. oil from remote tank has filled engine oil tank to level & buzzer cut off.engine oil filter is empty! i was told how to purge oil system remove phillips head srew from oil pump until i get oil there put srew back...
  4. G

    2006 hpdi ?

    Z200, cant find the blue? remote oil tank plug on the engine harness, also i want to mount the oil tank under console or is it better closer to the engine? Thanks for any info.
  5. G

    octane atleast 89 !

    what octane gas do you use in your engine? mid grade atleast with the older engine's ! 87 is p ss water! my 2 cents........
  6. G

    octane atleast 89 !

    what octane gas do you use in your engine? mid grade atleast with the older engine's ! 87 is p ss water! my 2 cents........
  7. G

    200 HPDI ?

    Whats a 2006 Yamaha 20O HPDI in the crate worth ? Won it in a tournament. Thanks Ol MAKO
  8. G

    90's 225-250

    Hello...want to put a single on a 25' mako. keep it light! what would be the most reliable. i know the 200's are pretty darn good, but not enough power? not lookin for speed just get on plane without over workin the engine all the time, seems like 225-250 no matter what make are more prone to...
  9. G

    Most reliable v-6 carb or not ?

    Hello...looking to repower a 25'mako with a used single engine, what ones have been the the most reliable? The old premium blend ? beside the rusty issues. Thanks for any info
  10. G

    Prop ?

    1990 200 johnson with 15x17 works fine on this 23 cc. repowering with 200 hpdi, will a 14.25-17 be a good start? <br /><br /> Thanks Ol mako
  11. G

    remote oil tank ?

    will a remote oil tank from a early 90's yamaha 200 work with a new 200 hpdi harness etc?<br /><br /> Thanks
  12. G

    Rodbolt!

    Please give me a call (434)252-8782 monday morning! will be in kitty hawk, hpdi? Thanks Billy<br /><br /><br />Old MAKO--------------53-04 Rockfish
  13. G

    200 hpdi

    Rodbolt ...i will be in kitty hawk to pick up a engine around 10 am monday morn, need your advice on something! my cell (434)292-8782<br /><br /> Hooters ....Thanks Billy<br /><br /> Old MAKO
  14. G

    Mako 261 or 254 hull

    lookin for a reasonable priced 25 or 26 mako hull, any condition!<br /><br /> Thanks for any info Billy<br /><br /> (434)292-8782
  15. G

    135 evinrude shuts down

    1976 135 evin cuts off above 4000 rpm after about 5 minutes, if i try to start it right after it shuts off it sounds like its trying to lock up! after about 30 second wait it will crank up and run, pumping plenty of water, compression between 125-130 on all cylinders, just ran it on the hose for...
See more
Top