Recent content by gidrac

  1. G

    What is this part called?

    Hi All,<br /><br />Please excuse my ignorance in this area. I am looking for a part for my 1997 Evinrude 150 HP V6 engine. The problem is that I do not know the name of it, nor where to get it.<br /><br />The piece is a black plug that screws into the back of the engine. I'm guessing it's...
  2. G

    Do I Need to Route my Hydraulic Steering Hoses Through a Rigging Tube?

    I will be taking on the task of installing a SeaStar 1.7 hydraulic steering system for my boat. I've read about running the hydraulic steering hoses through a rigging tube or pvc pipe. Is this necessary? I planned on just running them down the gunwale which is sealed up between the hull and...
  3. G

    Dual Cable Mechanical or Hydraulic?

    Since my previous attempts to correct my very tight steering were unsuccessful (read my previous post ) , I'm looking into replacing my current steering with a dual cable mechanical or a hydraulic system. (I figure if I'm going to pay 400.00 for a dual cable, maybe I should just shell out a...
  4. G

    Dual Cable Mechanical or Hydraulic?

    Since my previous attempts to correct my very tight steering were unsuccessful (read my previous post ) , I'm looking into replacing my current steering with a dual cable mechanical or a hydraulic system. (I figure if I'm going to pay 400.00 for a dual cable, maybe I should just shell out a...
  5. G

    Steering Not Frozen, but...

    really tight. I replaced my steering system (manual Teleflex) two years ago for my 150 HP Evinrude. Now, it's gotten really hard to turn again. And, if I turn all the way port or starboard, it will get stuck there and it takes a little more force to get it back around again. <br /><br />I...
  6. G

    Can I Use Existing Thrust Washer with New Prop?

    Hi all,<br /><br />I recently purchased a replacement prop from Michigan Wheel for my 1997 150 HP Evinrude engine. I'm having a hard time removing the existing thrust washer (part # 126870). I'm wondering if I can just leave it on and put the new Michigan prop on top of it. Could this be...
  7. G

    Can I Use Existing Thrust Washer with New Prop?

    Hi all,<br /><br />I recently purchased a replacement prop from Michigan Wheel for my 1997 150 HP Evinrude engine. I'm having a hard time removing the existing thrust washer (part # 126870). I'm wondering if I can just leave it on and put the new Michigan prop on top of it. Could this be...
  8. G

    I Need to Replace my Battery...

    and I'm not sure what to look for. I have a 20' Bayliner Trophy w/ 150 HP Evinrude engine. I have a two battery setup with a battery switch. I need to replace one of them. What's the best marine battery out there? Do I need some specific specs to purchase this battery, or is it just going...
  9. G

    Vortex or Michigan Match Props?

    Hi,<br /><br />I need to purchase a new aluminum prop for my Evinrude 150 HP V6. Which makes a better prop - Vortex or Michigan? Any recommendations on either?<br /><br />Also, do the props come with a new cotter pin, nut and thrust washer? Or, do these have to be purchased seperate? <br...
  10. G

    Mercury Prop Re-Keyed for Evinrude, but Still won't Fit

    Hi all,<br /><br />I had a stainless steel mercury prop re-keyed for my 150 HP Evinrude (at the suggestion of my Evinrude dealer/mechanic). The splines (I think thats what you call 'em) fit and the prop goes on nicely. The problem is that the prop takes up too much room on the shaft and...
See more
Top