1998 mariah z302 with mercruiser 502mpi and bravo3
when under way the boat lists to the starboard side. trim tabs will fix the problem but want to figure this out. i've tried moving stuff around including passangers.....still lists!
if the skeg on the bottom of the bravo3 was bent or...
i have a 1999 mariah z302 with a 502mpi and bravo3.
my motor surges when i come off crusing and drop into idle. somtimes staying at about 1200rpm. if i rap the throttle in netural a few times it will settle down to about 900-1000rpm.
i also have alot of trouble docking this boat. i think...
my 502 dies out at 4000rpm. put a pressure guage on the schrader valve and get 32psi at idle abd it drops to 30 psi with any throttle.i cant get the fuel pump to cycle all the time with the turn of the key, even if i shut off the batteries for 10 or so seconds. mercruiser says i need to produce...
i just bot this boat and it has a 502 mercruser. this is my first inboard motor. the problem is when it's cold or after it hasn't been started for a few days it will lope up and down till it warms up good. plugs are new, fresh oil and filter and fuel filter. fuel is fresh with pri-g additive. i...
i just bought a 30 foot mariah with a bravo 3. the problem is the speedo dosn't work.i've been told the pickup is in the gearcase. is this true? does it et clogged like a regular peedo tube? is there any way to check it's operation? thanks in advance....james
i recently removed my vro's and added a holley red fuel pump on my 250 V8. i also put on a new powerpack. when i back off the throttle to stop the warning alarm beeps rapidly for a couple seconds then stops. boat runs normal.any ideas on what the problem could be? it's getting quite annoying...
it's been a while since i've been here. i'm looking to contack dhadley to purchase a turbo ultima prop. anyone have a phone number to reach him? thanks...james
i'm looking to repower my 2600lb baja hammer with my 1991 250 v8 with a 2004 evinrude 225 HO hdpi. i need as much feedback as possible. i've done searches but came up with very little(guess thats good). thanks for any input!...james
i have the sea star pro on my V8 outboard.<br /> what is the best wy to bleed this system. i'm using it for a high performance application and need to get rid of as much side to side squish as possible. thanks in advance...james
4 of my 8 plugs are fouling out.<br /> i think there are valves to let unburnt fuel back to intake manifold. in the book it shows a syringe. do i need to remove them to check? wgere can i get a syrange to check with? thanks..james
4 of my 8 plugs are fouling out.<br /> i think there are valves to let unburnt fuel back to intake manifold. in the book it shows a syringe. do i need to remove them to check? wgere can i get a syrange to check with? thanks..james
i've been batteling this for a year now.<br /> motor run's good but should rev out more. i've changed prop and had the motor at two marina's. they say it's supposed to rev to 5500. all the experts say 6700 for this 1991 V8 250. i winterized it this weekend and the top two plug's on bolth side...
the header says it all! my V8 wont trim up when WOT. it will trim up on the trailer or when sitting still. it's not making any funny noises or going slower then normal. at WOT it will trim up about 25% then stop. any ideas? thanks...james
ok, i give up. the dealer told me that my V8 looper should only turn 5500 and i would be pushing it at that! i dont get it. the OMC service manual says operating range is 5200-5500 but the rev limiter is 6700. why wouldn't OMC make the rev limiter 5500 if that is all it's designed to turn? from...
since i've owned this motor, i've heard two or three diffrent beeping noises. anyone know where i can find out what diffrent beep's mean? i know when the oil resivor is low beep. the one i can't figure out is the warning that beeps over and over very quickly and get's louder and quieter. would...
