Recent content by hannez82

  1. H

    A surveyor around Dubuque,Iowa

    Hi, Im interested in a boat located in Dubuque, Iowa but lives in europ? so I need a surveyor to take a look at the boat. Does any one know of a descent surveyor in that area? Best regards Hannes
  2. H

    Knock sensor without y-fitting in merc 350

    Hi, I have a merc 350 from -95 with a thunderbold V with knock sensor. When I bought the engine the knock sensor(806612T) and y-fitting (22-806705) wasn't in place. The y-fitting is not sold anymore but I got a tip that I can put the knock sensor directly in the block. It is possible to do so...
  3. H

    Mercruiser V6 -> V8 swap, engine mounts

    Re: Mercruiser V6 -> V8 swap, engine mounts I need a tool like this one. What is called? If the first hole in v6 and the second is for v8 I have my answer right there.
  4. H

    Mercruiser V6 -> V8 swap, engine mounts

    Hi, I'm about to swap from a V6 to a V8 mercruiser in my Bayliner 2455 from 2000. I shall move my engine mounts and need to know how much. I've read on the forum that I should move them 4.4'' forward but somewhere else I have read 3''. Can someone say for sure it's 4.4'' or if there is a...
  5. H

    Compression test on a Mercruiser 350 form -96

    Hi, I have put together a mercruiser 350 from -96. The engine is not started yet but today I made a compression test and the result was that most of the cylinders had around 8 bar but one(nr 8) had 6.5. This particular cylinder is sleeved, has a new piston and new rings. The others is only...
  6. H

    Rear engine lifter eye mounting

    I'm putting togheter my mercruiser 350 -95 pre-vortec. I don't know if I have mounted my read engine lifter eye correct. Should the lifter eye be behind the bolt that holds the manifold or should be outside as in the picture?
  7. H

    Fel-pro Q17030, needs extra sealing

    Hi, I'm putting together my mercruiser pre-vortec 350. I have bought the Fel-Pro head gastket Q17030 (Fel-Pro Performance Head Gaskets Q17030 - SummitRacing.com). The mercruiser says that ribbed steel head gaskets needs extra sealing on both sides of gasket but graphite composition doesn't...
  8. H

    Gasket conversion set, parts?

    I bought this Gasket conversion set from summit: Fel-Pro Performance Full Engine Gasket Sets Q17125 - SummitRacing.com There are two parts that I don't know what its for, can someone enlight me? :) BR, Hannes
  9. H

    Gasket between oil pump and main bearing?

    I'm about to install my oil pump om my mercruiser 350 from -96. I can't remember any gasket between the oil pump and the main bearing during disassemble and can't see anything on the exploded view. It feels like it should be a gasket there?
  10. H

    Installing casting/freeze plugs in 350 block

    I'm about to install the three casting plugs on the front of a 350 block from -96. The manual says nothing about how it's done. Should I just hammer them in? Do i need to seal them with something? Thread sealer or something like that? How far in should they go?
  11. H

    Clevite cb663p,

    Hi, I bought Clevite cb663p to my 350 but when I compare the old bearing with the new one they don't look the same. The old one has a cut as pointed out in the picture. The old berings are also cb663p. What is the cut for and why isn't it on the new bearing?
  12. H

    Does this piston need to be replaces

    Re: Does this piston need to be replaces Hi, Here is a picture where you can see most of the piston crown. Br, Hannes
  13. H

    Does this piston need to be replaces

    Hi, I'm putting my mercruiser 350 fron -96 together. Does this piston need to be replaces, it's a 423NP piston.
  14. H

    Plate between manifold and carburator

    Hi, I'm assembling a mercruiser 350 from 96(pre vortec) and I found this plate between the manifold and the carburetor(Weber 4 b). I can't find the plate in the manual and I wonder what it's for and if I should keep it. / Hannes
See more
Top