Recent content by HybridMX6

  1. H

    2000 55hp Commercial Johnson Charging - How To?

    I have a 2000 55hp Johnson commercial outboard. It was bare bones manual everything when I got it. I've since converted it to electric start, remote control, and added a CMC TnT, but I'd really like to set it up to charge my starting battery while running, since I use it for lights and GPS/Depth...
  2. H

    Prop question - weak top end and slow hole shot

    I've had this motor for about 5-6 years now, it's a 2001 Johnson 55hp 2cyl commercial outboard, with an odd 23" shaft. Outboard is/was manual everything. I've since converted it to power everything, including a CMC PT130, and when that was mounted I used it to raise the outboard the 3" I needed...
  3. H

    Early 2000's 25hp Mecury Tiller - stuck in Reverse

    Well, I'm trying to help a friend out who has an early 2000's 25hp Mercury. It's a tiller motor, 2 stroke. We went out fishing last week and the motor was fine, hit something in the water as some point, but shut motor off, checked LU and prop, all seemed fine, so we carried on. Used both F and...
  4. H

    Help wiring keyswitch to starter and solenoid and battery

    Ok, let me warn ya first, this is being hooked up on a 2000 Johnson 55hp commercial outboard. Engine was manual everything when I bought it, start, tilt/trim, steer. I've converted it to console and remotes, CMC TnT, and the last thing I'm trying to hook up is an electric start. I don't care if...
  5. H

    throttle/shift parts - anyone have these they'll sell?

    Well, no one local seems to be willing to part with a few parts, and can't find a local blown powerhead, so was wondering if anyone here would happen to have 2 parts I need pretty bad. Here are the part #'s, and descriptions from BRP: 437147 - throttle lever bracket 341295 - throttle lever...
  6. H

    2000 55hp Commercial Remote Controls?

    Hello, I'm still in the process of converting this manual everything motor to work with a console. I'm in no rush as I don't have the console built yet, but do have all the supplies to make it. I am trying to find out which control I would need for this engine. Right now it's manual start...
  7. H

    2000 55hp Commercial Starter ?

    Hello. I've been working on getting this motor set up with an aftermarket TnT and also doing electric start on it. I'm trying to see if I can't save some money over the $400+ cost of the whole kit, but can't find a part # for the starter itself. All I seem to be able to find are part #'s for...
  8. H

    Need Part # help for '99 25hp Merc

    Hello. I'm usually over in the OMC section since I own 2 of them, but my friend is asking me for help with his 1999 25hp Mercury outboard. I tried (honestly) to go through Mercury's website and find the part #'s, but I found it confusing since I am used to how BRP has their site, and IBoats...
  9. H

    My luck and a thank you to a stranger

    Ok, so this past week I pulled my lower unit off my 2000 55hp commercial motor, as well as both carbs for rebuilding. It wasn't running on both cylinders at idle, and I had verified spark was good, which left me with no or not enough fuel. Only did it in gear, oddly. Anyways, the water pump was...
  10. H

    Need Part # cross ref please ~ 1992 or 1993 60hp 3cyl

    I have this Johnson 60hp I've been working on now forever. It's getting annoying. I've rebuilt the entire engine, it runs fine, but the only thing I can't figure out is the t-stat. I was told it was a 1994 when I bought it, but the transom tag is missing and the welch plug is useless, motor's...
  11. H

    Cylinder Head Part # Cross Reference Please

    Hello. I'm still trying to figure out what year this engine is, or at least parts on it. I've got a t-stat and all associated parts for a 1993 and they do not seem to fit this engines head. My part # on the engine is 329835-4. When I bought it I was told it's a 1994, after doing some work on it...
  12. H

    Tilt and Trim Switch on Controls Up stopped working

    Well, it never stops with this thing. I'm finally about done with this '93 60hp motor rebuild, and now all of a sudden the tilt/trim switch on the controls doesn't work for going up. It is fine with going down, but not up. It still works on the motor just fine (the switch on the side of the...
  13. H

    1993 60hp T-Stat question

    Ok, I've got this motor running as I feel it should with the exception for one thing. When I got it there was no thermostat in it at all. I have ordered all the missing pieces and have them sitting at home. All I had to start with was #14 in the pic below, thermostat housing, and also #44...
  14. H

    1993 60hp Fuel coming out of carbs

    Hello. I finally got the hoses all done and got this project to the "ready to start" phase. I pumped the primer ball, pushed the key in, and then turned it (I didn't hold the key in). Motor tries to start then dies. I searched and found some info about to squirt premix in the carbs and see if it...
  15. H

    1993 Johnson 60hp 3cyl 1st Start on Rebuild ???'s

    I have finally finished putting this motor back together after 6 months of having to taken apart. Took more money than I had planned, and I had some unexpected bills in the middle of it that set me back and made me put off getting this thing done. Anyways, I'm hoping to get the remaining fuel...
See more
Top