Recent content by IVAN QUINTANA

  1. I

    boat project on the rise

    <br />hello everyone :) <br />i got my computer up and running again so i posted these flix.<br />the first picture was last month,now the frames are all glassed in to the stingers and i started pouring foam but ran out so im waitting for more.<br />my quetion is on the bilge cavity,my fuel...
  2. I

    how do i post a picture or two

    i went and got a roll of film on a CD today<br />of my boat project because im running into<br />problems as my slow progress moves along,<br />they say a picture is like a thousand words :D
  3. I

    year&a little info

    got a murcury 9.8 thunderbolt ign,ss#3614710.dont have a year yet :confused: <br />any manuels recomended,thanx in advance :cool:
  4. I

    carb trouble

    Im working on a 71 evinrude 25hp.s#251025-E07230<br />after a major tune up i put it in a tank and did all adjustments,I ran a gallon of gas through it and shut her down,<br />the very next day it would not give me a cold start.new coils& points new fuel pump but no fuel in the cylinder,if i...
  5. I

    bilge&deck drain

    Im back to my boat project and read jasonj"s post, we cut are boats up about the same time only i removed the top hull and cut back the deck a couple feet,I replaced the transom,glassed it in and put the top back on with a new rub rail.<br />My boats a 19ft glass runabout V hull,its a 1978...
  6. I

    boat motor cover weatherstrip seal ?

    anyone know where to get the weatherstriping that raps around the motor cover of a 71 evenrude 25hp, I know its old but i just recondiction the motor and painted the cover, the old rubber seal was stapled on with heavy gauge staples,I took a peace of it to a couple of local marine places and had...
  7. I

    112 outboard removel

    im prepairing to lift off my motor,im using my garage door casing to hang it from,wraped a chain around the 4/12stud,<br />my questions are,the lifting fixure descibed in the manual the one that bolts to the flywheel,is that all that holds all the motor wight?<br />where would i find one?<br...
  8. I

    Oars

    does anyone know the proper lenth oars for a 15ft Gregor.<br /><br />Thanx :)
  9. I

    concerned on transom crack

    hello to all who share this site :) <br /><br />I recently bought a 78 stuery with a 94 johnson 112spl. Im working on painting it, and found a deep crack along the top of the transom, both sides going horizontally and one crack moving vertically in the middle of a main bolt,someone installed...
  10. I

    a little info on a 112-spl

    hello out there,<br />I bought this older boat over the weekend,<br />1978 19ft fibberglass steury,outboard,<br />the motor covers been painted so theres no stickers but theres a plate on the cover and it saids 112-spl,(mod#j112tsxers,ser#G 03587895)<br />The controls are evenrude so i asume the...
  11. I

    Opinions on old boat

    I bought a 19ft 78 stuery fiberglass boat with a<br />110hp evenrude outboard,<br />Its been kept in good condiction and the guy i bought it from is a boat dealler,<br />I was woundering about the boat manufactor.<br />and the quality.<br />Any info would be great.
  12. I

    long shaft mariner

    hello again to all,and a good new year.<br />I bought this 15hp mariner(ss#684c L551365)<br />i got a manual with it but unsure of the year?<br />Also it came off a pon toon and the shaft looks <br />pretty long,I have a 14ft starcraft bass boat.<br />Is the motor size OK?<br />THANKS IN ADVANCE.
  13. I

    need help tuning my rude

    hello again, <br />Im trying to get a 71 25hp evenrude model#25102-03,tuned and ready , I cant seem to find the<br />main harness plug anywhere and my shoulders about to pop,so i ran jumper cables to the motor<br />and just tap the starter :confused: <br />ahyhow it started but runs rouph then...
  14. I

    Need part #or sub

    I need a little help finding apart,<br />the wiring harness plug,that connects battery to motor.25hp EVENRUDE #25102-03 Is there a part #?<br />Thanks a million freind
  15. I

    I need help finding the year to a 25hp evenrude

    I GOT A 25HP EVENRUDE FROM A FRIEND,SERIAL#25102S-E07230, I got it to start and it sounds strong but its in need of some big time work,Can some one help me find the year and where to get used parts?
See more
Top