Recent content by Jango

  1. J

    1996 Stratos 258

    I would like to get the specs on a 1996 Stratos 258 such as: 1. Length at centerline 2 Beam 3. weight w. 90 hp Evinrude(also max HP) Any other facts available would be appreciated - Thanks
  2. J

    Inboard Transmission

    Does anyone out there know where I can purchase a Good Used or Remanf. Borg Warner (Velvet Drive) 71 Series, 1:1 ratio Transmission. Thanks in advance.
  3. J

    What is Ficht ?

    Silly Question? What does Ficht stand for? I've heard a lot of good things about Direct Injection. Is this the Same as Ficht? What are the differences? Thanks
  4. J

    More Power From an Outboard?

    Has anyone tried to increase the Power Output of an Outboard? How about milling head (increase compression ratio), increase Reed opening by either larger reeds and or opening Reed more? Opening both intake and exhaust ports? I realize some of these possibilities are on the drastic side but you...
  5. J

    Removing Side Glass from Bayliner

    I am in the process of removing the side glass from my 88 Bayliner. My problem is removing the Aluminum Frame from around the glass. I would like to reinstall the Aluminun around the windshield to better finish the job. I can not find a release agent to seperate the Alum from the Glass. Have...
  6. J

    Good Decarbonizer for "Trent"

    Trent, Do you use the B-12 as a Fuel additive or Spray it into the Carbs? If you Spray, how much?<br />Thanks, John
  7. J

    Force Tilt /Trim question for Clanton

    I am confused as to the BEST Fluid for 1988, 85HP Force Tilt/Trim. The "CLYMER" Manual Lists 10W-40, for External Pumps,which I believe I have. On other Topic someone assumed this means NON-DETERGENT. I am not aware of any 10W-40 Non Detergent Oil. Also on an another Topic Clanton suggested...
  8. J

    Force Power Trim Current Draw

    Does anyone know the approximate current Draw on the Force/Chrysler Power Trim Motors. I will be installing aftermarket relays and need to get large enough? Don't want to burn up the contacts.<br />Thanks<br />John
  9. J

    Force Tilt & Trim Testing

    Just installed used Tilt & Trim on 85HP Force.<br />Tried to "Bench Test" prior to permanet wiring etc. Unfortuanately I do not have my Shop Manual yet. (on order for over three weeks from Amazon)<br />Tried puting +12V on Green and than on Blue - no action. Next, I checked res. between motor...
  10. J

    20HP Mercury "Surging"

    I recently had the Carburator on my 1975 Mercury 20HP rebuilt. Now occasionally at WOT the Motor will "Surge" or loose rpm momentarily. Is this caused by wrong float level or could it be something else? At less than WOT it runs fine.<br />Thanks
  11. J

    Draining Lower Unit Lube

    Would like to drain and refill gear lube in lower unit, but do not know how lube will drain since both VENT and FILL holes are next to each other above cavitation plate,well above gears. Does one tilt motor out, which should drain most lube? How to refill?<br />Motor is an 85HP Force and has a...
  12. J

    How Does It Come Apart?

    Trying to remove Backrest Upolstry from 88 Bayliner Capri - Two Panels in Back, on each side of Motor. I'm thinking there must be a "Z" bracket of some kind fastened to the Fiberglass and the panel hooked over???Tryed prying UP, PUSHING down - no luck. Would appreciate it if some one could help...
  13. J

    What's the secret ( Firing it up )?

    Just bought a Bayliner with an 85HP Force. It runs great, but I haven't found the secret on how to start it (COLD). I've tried holding in the key (choke) for a second or two. Tried holding the choke on continuously. Only after 2 or 3 min of cranking, the motor starts. After warm up, it starts...
  14. J

    Power Trim wanted - 85 Hp Force

    I would like to install Power Trim on 85 HP Force (1988 motor)Does anyone have good used one for sale?<br /> Thanks John
  15. J

    Propeller Size & Pitch

    I have a MICHIGAN, no. 072127, prop on my 85HP Force. Would like to know Prop Pitch and also gear ratio on this motor. Thanks
Top