i just got a used boat and i found a pin hole size leak where a old transducer screw was installed what is the best way to stop the leak type of sealer to use. its a fiberglass bonita boat.
i just bought another boat it has a 1978 85 hp evenrude model 85895 i dont have a manuel for it yet and i needed to find out the gap on the sparkplugs the numbers are Br8hs plug and what would be the fuel oil ratio fot that motor .is it 50 to 1 like my johnson 1986 40 hp.
i just purchased a 15 hp 4 stroke suzuki that came with two props ones a four blade and ones a three blade what would be the differance i would experince between the two props
i was running a 2001 8 hp 4 stroke on my tracker 15 foot for the size the motor did a good job i upgraded to a 2008 15 hp 4 stroke suzuki i never owned a suzuki how are these motors what the word on them .
i have a 2008 df 15 suzuki four stroke just picked up engine starts fine but bogdown when throttled up what does this sound like it could be .im going get some plugs and a fuel filter some non e fuel and see what happens .
i have a 1985 Evinrude mod #e25rcos that wont shift into reverse unless you take your finger and lift up on this plastic shift pawl on the shift lever no more then an 1/8 of an inch and it goes right in reverse i think in just needs an adjustmine but how is that done does anyone know of this...
i have a 84 jonnson 40 hp 1984 J40ELCRM Johnson and i need some help i changer the impeller and now im getting water squirting from the seam between the lower unit and midsection and the pee stream isn't as strong as before did i do something wrong? ok i took the lower unit off again and it...
i have a 84 jonnson 40 hp 1984 J40ELCRM Johnson and i need some help i changer the impeller and now im getting water squirting from the seam between the lower unit and midsection and the pee stream isn't as strong as before did i do something wrong? ok i took the lower unit off again and it...
i have a 84 jonnson 40 hp and i need some help i changer the impeller and now im getting water squirting from the seam between the lower unit and midsection and the pee stream isn't as strong as before did i do something wrong?
i changed the impeller and houseing and started it up and water is squirtring from the seam that between the lower unit and midsection and the pee stream isn't strong did i do something wrong? Does the water tube just fits as the unit is going up.
i'm planing on looking at a 2001 YAMAHA 8HP 4-STROKE - for $1,095.00 are these good engins and what do you think of the asking price .its been all serviced and ready to go.
i got this boat for three hundred what do you think i could get now check out my photos this link is when i first started photo 2 and here is my latest photo 6 http://s871.photobucket.com/albums/ab279/sid2jay/?action=view¤t=Picture1574.jpg
my shift rod has a curve at the top it a 84 johnson 40 hp j40elcr what direction does the rod point to i put my lower unit on and it wouldn't shift into reverse so i dropped it again pushed down on the rod and it was in nutural and the shift was in the nutural also i didn't replace it yet i...
i have a 1984 johnson 40 hp j40elcr and im changeing the impeller for the first time i removed the four bolts that on the outside of the lower unit i removed the bolt that holds the trim tab on and i removed the long bolt that was underneath it the lowre unit droped about 3/4 of an inch and...
i have a 84 johnson 40 hp and i removed the head cover to install a new thremostat and i wanted to change the temp sensor as well .how is the sensor removed do you just pry it out of the hole or do you have to remove the head.
