Hi All does anyone know what size the Woodruff key is for the flywheel to slide onto I have somehow misplaced mine for a 33 hp johnson 1968 just wondering what the part size might be as i can just get these at the local hardware store for cents on the $.
Thank you
James
Just a quick confused question here i have a 9.5 evenrude and when the cowling is off it it runs like a champ however as soon as i put the cowling back on it runs really boggie any ideas? it is a 1969 I have the needle turned out about 3/4 of a turn what is what I normally run them at but I...
Just wondering if it matters what position the throttle handle is in when resetting point gaps on older motors sometimes i set them and the motor works great other time i set them and them seem sluggish not sure if throttle position has anything to do with this.
Thank you
James
Hi all
I'm currently working on a 72-73 merc 7.5 with this being said its not the one with the fuel pump built into the carb.
My issue is i can get it to pull over and run for about 5 min and then it seems the fuel line goes empty and the motor quits if if I prime the ball while its running...
Hi all
This is my first time working on an older Merc and well they seem easier and tougher then evenrude/Johnsons in the end Ijust got this ole girl to run however on the tiller throttle it seems there is alot of slop in it from when it turn it to the fast position to full out it takes about a...
Hi all,
I have a 70-80's johnson 15 and it seems I'm not getting fuel when i prime her she runs then after 10 min does if i keep pumping the ball she keeps running I changed the fuel to carb line with a clear line and it seems to me that I'm not seeing any fuel pumping into this line the fuel...
Hi all, I have a 9.5 evenrude sport twin and cant seem to get the carb to prime when i squeeze the ball it just pumps air and fuel into the carb and the fuel comes out a small port on the top of the carb by the choke. any Idea what may be causing this.
Not sure whats going on here replaced head and water jacket gasket the other day took motor out ran like a dream never had it run so good then took it out today runs great at half throttle then when going full out motor revs high almsot like prop is covered in weeds gets that low deep hollow...
Hi Im currently attempting to restore my old 1968 33hp Johnson shes already in good shape howevers i did notice my headgasket was in pretty bad shape so apon replacing it discovered the last person to do so had removed the waterjacket gasket and just siliconed it shut im just wondering if anyone...
Hi all im in Canada here and i have a Johnson 3hp early 60s small white motor seems i can get my highspeed set very well however i cant get the motor to go lower then the start position without stalling out my low speed needle seems to have a small bend in it and thus looks like it has been...
Hi i have a15 hp 1986 evenrude it was over heating i just replaced the head gasket and water pump housing slip plate and impellor i dont think its overheating anymore i ran it with both muffs and barrel noticed the barrel after about 2 hrs of running it was at a slow trickle but this might have...
Hi all i have a 3 hp johnson 1`960 is the small white one with the high low needles in it i have great spark good compression however it seems fuel maybe the bad guy on my end just wondering how many turns from gentle seat out it needs to start her up as im about to put a new carb kit into her...
OK so i have a 1986 Evenrude 15 hp ive now changed the headgasket along with all the other gaskets included in doing this removed the thermostate and as well replaced just the impeller however not the waterpump housing as it did have some slight damage but still looked ok my question here is...
Hi, All i have aevenrude 15 hp 1986 dosnt seem to have a thermostate hopusing so im not sure about that however i just replaced the impellor it began to pump water again but will only pump at idle when rpm and motor is running in high impellor quits pumping andf motor begins to quickly over...
Hey all i just recently took my motor outta winter storage changed the plugs and cleaned the plug harness spotless and when taking it out today i noticed at low rpm on warm up it misses and almost stalls catches up and then will continue like this untill it almost stalls once warm tho this issue...
