Current visitors

Home
Members

jerryjerry05's latest activity

jerryjerry05 replied to the thread 1979 chrysler 4 hp carburetor squirting fuel.

There should be no packing material around that screw. Do as Racerone suggested.

Sunday at 4:12 AM
jerryjerry05 replied to the thread 1990 Force outboard lower drive issue question.

To start a PM, Just click on my Pic and it should open a page that you can start a PM. If your motors dies at low RPM's it could be...

Friday at 6:53 AM
jerryjerry05 replied to the thread 1990 Force outboard lower drive issue question.

Sorry I've been gone and haven't read the post. I can't explain the procedure but can send the manual so you can read all about it...

Apr 17, 2025
jerryjerry05 replied to the thread 1990 Force outboard lower drive issue question.

IF??? the code's not on the top of the casing it probably needs to be shimmed the old way. Looking down at the top of the drive into the...

Apr 14, 2025
jerryjerry05 replied to the thread 1990 Force outboard lower drive issue question.

Nordin, that's what the manual I have covers. The newer coded gear cases.

Apr 9, 2025
jerryjerry05 replied to the thread 1990 Force outboard lower drive issue question.

What are you using as a service book or manual?? They put out a Service Manual, Lower Unit 85-150 H.P. OB 4527 Issued in 9/89. It covers...

Apr 8, 2025
jerryjerry05 replied to the thread Starter getting only 4 volts.

New battery could be bad? Load test it. The cables could be bad?? Check for swelling along the length of the cables and bad connectors...

Apr 8, 2025
jerryjerry05 posted the thread Water in oil in Mercury & Mariner Outboards.

Mercury 1150F23ED 2B714430 A friend just bought this motor and boat combo. The boats a 2021 got it home and doing "stuff" to his new...

Apr 3, 2025
jerryjerry05 replied to the thread 1974 Chrysler 120 HP No Spark.

Post a pic of the ignition system. Try outboardignition.com once you figure out the system.

Apr 2, 2025
jerryjerry05 replied to the thread Lower Unit Bearing Carrier Leaking.

Thanks for the pics. No O-ring at all??? HOW??? did it not leak??? WOW They must not have pressure tested.

Mar 23, 2025
jerryjerry05 replied to the thread Troubleshooting 91 Force 90HP Tilt/Trim System.

That style pump didn't have a relief valve. Most of the older Force and some Mercury style pumps didn't have it. When needed the first...

Mar 21, 2025
jerryjerry05 replied to the thread Troubleshooting 91 Force 90HP Tilt/Trim System.

That pump: there's nothing in there that you can fix. That's the pump, the part that's leaking is in the bottom of the housing. Open...

Mar 19, 2025
jerryjerry05 replied to the thread Lower Unit Bearing Carrier Leaking.

I found a puller with long skinny arms that works. You might need to use some heat to free the carrier, thin aluminum so be careful not...

Mar 18, 2025
jerryjerry05 replied to the thread Troubleshooting 91 Force 90HP Tilt/Trim System.

Unless the tilt ram is leaking??? I wouldn't mess with it. 99.99% of the time the T@T pump is where the problem is. I see in the pic...

Mar 18, 2025
jerryjerry05 replied to the thread Attempting a motor rebuild.

Yup take the edge down a very tiny bit. If for some reason you decide to take the carb and reeds of to access the roller bearings, make...

Feb 8, 2025

Show older items

Home
Members

Top