Recent content by Kanadakid

  1. K

    Cowling Blew off on Highway / What are my replacement options ?

    The Cowling / hood on my 2006 Yamaha 115TLR blew off somewhere between Harrisburg Pa and Heston , Pa. If you see it please send it home. In the mean time I need to replace the cowling. Yamaha says they do not supply this any longer. However the pre 2006 115's and 130 Hp look the same. Does...
  2. K

    F90 Power Trim Re-build

    Hi gents, It has been a while since I have been on. I have taken this unit off my boat, who can re-build the seals /valves on this power trim. It will not hold the engine in place and sinks down. Have bled the system a few times and can't get it to stop sinking. Thanks Kid
  3. K

    Where to send my Tilt trim for re-build

    I have removed the power tilt trim off my Yamah F90. Who can I send it to for re-build ? Thanks Kid
  4. K

    F90 Without Power T&T

    Question: Removed the power T&T. If I use a trim bar can you run this engine with just the top pin without the Power T&T ? Thank you
  5. K

    Replacing F90 Manual Relief Valve

    Tilt trim won't stay up and sinks down slowly after a few minutes. Tried bleeding the system and next on the list is replacing manual check valve. Took it out and it is very small with a tiny ball bearing behind it. how do you get the rest of the valve out and replace the whole thing ? I...
  6. K

    Power Trim Slowly Sinking Down

    2003 Yamaha F90. Last fall my power trim would move up and down with no problems but you could watch as it was in the trim position sink downwards. We opend the system and bled some air out of it and it worked much better how ever while running the engine will sink back down every 2 or 3...
  7. K

    So far not good / F90 Timing Belt - Valve ck

    Gents, I'm posting my progress of this job so that others may benefit from my learning curve. Well I though I had everything buttoned down to do this job. Not! These are my Awe S__ts so far. 1) Flywheel holding tool I have doesn't really fit. I can angle it so that the pins on one side...
  8. K

    Go No Go feeler guage / Angled

    Gents, I can find go no go feeler gauges and I can find 45 degree or angled feeler gauges, but Who makes or where can I find a go no go angled (45) feeler gauge to check my 2003 F90 alves? Thanks Kid
  9. K

    2003 F 90 valve adjustment

    Hi gents it has been a while sine I have posted, was having difficulties logging in and finally got straightened out. I am just preparing to change the timing belt (even though it looks fine) at the 5 year mark. I am also going to check the valve lash with a go no go feeler gauge. I am...
  10. K

    Broken Speedo Stick

    I have searched the intranet and on the forum and can't find anything on replacing the speedo stick or where to buy on. We had to pull the Boat onto the bank to do some emegency leaf clearing back in the fall and the stick snapped off. Appreciate you help with this Kid
  11. K

    Air Filter F 90

    Is there ever a need to replace the air filter on am F90 ? I see it on the engine but don't see anywhere in the manual when and how to change it.<br /><br />Thanks<br /><br />Kid
  12. K

    Engine Fuse / 20 A blowing

    Gents,<br /><br />I'm trying to determine what wires could be shorting and blowing the 20 A fuse in my 2003 F90.<br /><br />When it blows, the engine won't do anything. Turn over, click, nothing. The trim /tilt won't go one either.<br /><br />It is the weekend and wanted to try and determine...
  13. K

    F 90 Blowing fuses - help please

    Ben C and Willie helped me last week finding the fuses. My engine keeps blowing the 20 A light green fuse. I have disconnected all of the accessories and it still shorts out. It is intermittent. <br /><br />I blew 3 fuses today but its working fine right now. I cleaned the terminals and...
  14. K

    2003 Yam F 90 - No start

    Could use some help /direction.<br /><br />Engine ran fine all day started right up, ideled smooth, ran some at WOT and mostly @ 3/4. Last 500 yards I turned on the Bilge pump. Slowed down so I could look behind to see if any water was coming out. There was none.<br /><br />Engine started to...
  15. K

    Re-wiring transducer

    Gents,<br /><br />My x 51 transducer broke just before the bracket. I ordered a replacement transducer. I was thinking the only way to re-wire this unit was to cut the old transducer from the wire, tape the plug end to the wire and pull it through. However it looks like a tight fit and it it...
See more
Top