Recent content by KScott78

  1. K

    Force 125 won't turn over

    Hello, I have a 1989 Force 125hp outboard. I used the boat 4 weeks ago for an entire weekend without issue. Now getting ready to leave for the long weekend and I can't get the motor to turn over properly. It turns very slowly, like the battery is almost dead, but the battery is full and I also...
  2. K

    flywheel balance

    Hello, I've been working on a 72, 18HP Evinrude. Had to replace the coils but the flyer was wouldn't come off without some work, I started using the puller I had a available in my garage, one with the arms and hooks ( I know this is not recommended ). Anyway I broke two small pieces of of...
  3. K

    selecting a prop

    Hello, I'm selecting a new prop for purchase and I was wondering. The prop I've found is a 'through' hub, but my engine is a single exhaust. ( 1989 125HP Force ). does it matter if I use the 'through' hub, will it fix correctly, any disadvantage? I'm looking at a Solas, #1411-130-19. thanks...
  4. K

    Static Timing?

    Perhaps a stupid question, but could someone please explain to me; what is static timing? thanks in advance for your help!
  5. K

    Fuel Line

    Hello, I have an 89 Force 125, the fuel line going to the carbs has a crack in it, part# F438754. This is a very dense plastic/rubber tube. My question; is there any reason why I can't just replace this with a normal fuel line? $40 for a replacement seems a little steep for 2' of hose. Also...
  6. K

    Skeggard?

    Hello, I broke off a bit of my Skeg last summer, I was looking at buying a parts motor but then came across this product. I'm wondering if anyone else has used the Skeggard? What did you think of it, or was there a similar product that you preferred? thanks in advance for your time!
  7. K

    89 Force 125hp Timing

    Hello, I need to set the timing on my 1989 Force 125hp, It was completely rebuilt last year. I've watched the video at the top of the forum on the link & sync + timing. However it's unclear what exactly the timing should be for this engine. I've read 28 degrees, but is that at full throttle? If...
  8. K

    Power trim/tilt on 89, 125hp

    Hello, I've recently purchased this motor and it runs great, however I have some questions about connecting the tilt/trim to my throttle/shifter. Attached is the schematic for the unit. I am able to make it work if I connect power/ground to the blue/green wires that come directly from the...
  9. K

    Force 125hp Prop

    Need a prop for my Force 1989 125HP, Model 1254X9B. Looking for used props in my area since shipping takes a while. Will the following prop fit? http://boatpropellers.iboats.com/Michigan_Wheel-Michigan_Match_Aluminum-Propellers/011003/ Also, will Mercury props fit on a Force motor?
  10. K

    Electrical Issue

    Hello, I've got a 1989 Force 125hp that I just purchased used ( I'm not a mechanic ). When connection the battery I know the cables are getting hot. After some testing with my multi meter I've found the that issue appears to be with the starting motor, when it test resistance from the positive...
  11. K

    Controller for my 73' Merc

    Hello, I have a 73' 115hp and I need new controls for it. Can I use any mercury controls or only certain years/hp?
  12. K

    Four Winns Engine type?

    Hello, I recently purchased a 1998 Four Winns Fling, I know it has an Evinrude engine but I can't seem to figure out which model. Any help would be greatly appreciated!
  13. K

    Best prop for 81 Johnson 60hp?

    Hello, I'm wondering what would be the best aluminum prop for my 1981 Johnson J60ELCIH 60hp? We use it for tubing and fishing mostly. thanks, Ken
  14. K

    1986 J60ELCDS Johnson Spark Plug Gap?

    Hello, just wondering if anyone could tell me what the park plug gap should be on a 1986 J60ELCDS Johnson. thanks! Ken
  15. K

    alternator?

    Hello, does anyone happen to know if my 1986 Johnson 60hp would have an alternator to keep my battery topped up? thanks!
See more
Top