Hey guys,, just put in a new triangular engine coupler & driveshaft,,, how much grease does this set up take being brand new,, I put in 12 pumps of Castrol poly blue,, Let me know,,, finally getting this back together !!!!!!!!!!!!!!!!!!!!!!!!!!!!!
I am still trying to get a "round " style coupler to go into my crank/flywheel. Since my 1985 motor was shown taking either/or style coupler, and after seeing a recent post of someone here swapping a newer motor that was blown to an older one. He also went from a round style to a triangular one...
Ordered a engine coupler #76850A-2 for my 1985 4 cycl. 120 hp. merc. motor. Serial # A492171. Old one was round, Started to assemble today, and coupler would not sit down against flywheel. My friend measured the protrusion on the back of the coupler and the hole in the flywheel where it goes...
Ordered a engine coupler #76850A-2 for my 1985 4 cycl. 120 hp. merc. motor. Old one was round. Started to assemble today, and coupler would not sit down against flywheel. My friend measured the protrusion on the back of the coupler and the hole in the flywheel where it goes and the coupler was...
Trying to get my 1985 I-MR outdrive back together, replaced coupler,gimbal bearing,all bellows & hoses & switches & cables and bought all Merc. products !
When trying to align motor, bar never did slide in "easy" Obtained even grease marks on bar,but when turned motor 90 degree's,, bar started...
On my 1985 merc. outdrive, that I am assembling. I bought shift shaft bushing kit #23-806036A1 from merc. It came with 2 brass bushings and 2 hard plastic seals.
Are the plastic seals for another model? As, there was no plastic seals, or room for them when I removed the bottom/bigger one, from...
Hey guys,,I am trying to replace my bellows,, I am using your technique of a 9/16th spark plug socket backed by a 11/16th plug socket. I cannot get the brass nut to come loose and it is now starting to round off ! I tried SOME heat, in case locktite was used !
Any recommendations as to my next...
Ok,, here's my first of many questions,, A 1985 merc. I-MR outdrive with a 120 hp. motor. I bought a Merc. gimbal bearing,, after getting my old one out,, and comparing,, the new one has no hole in the outside diameter,, I am assuming it is the newer "permalube" type ...
I have a 1985 Alpha outdrive,, what is everyones opionion ??? put an exhaust bellows back on or a tube ?
This is my first time for tearing my outdrive apart this far !! So far everyone's advice has been invaluable ...
I'm ready to slide my engine forward, to get to my engine coupler. It is a 1985 merc 120 hp. Obviously I will hook one end of my chain to either lifting hook, attached to the front of the motor. Now the question is,, if I split it at the flywheel housing, where do you think would be the best...
1985 Mercruiser 120 hp.
# A492171
Aplha outdrive
Which engine coupler came on this engine ? I believe mine is bad !
You should be able to see some splines when pearing up thru the gimbal bearing correct ? I am preparing to slide the motor forward, BUT want to make absolutely sure before I...
1985 Starcraft HL 181
4 cycl. GM. 120 hp. 2.5 liter
I-MR Outdrive
While out on the lake tubing & swimming with the family yesterday, we ran into an unexpected shallow spot. we were only going at an idle, but we did hit the bottom, and looking at the prop, must have hit a rock ! The boat seemed...
have a evinrude outboard,, can anyone give me the general information concerning this motor ?
1. Year
2. gas/oil ratio
3. any other relevant info ??
The model number is: 10302D-EO6196
Thanks,,, Allan
Hello all,<br /> Giving the interior of my boat some TLC,, now that the weather is starting to break ! Pulled my drivers side,,side panel off,, to replace torn vynil and wood was starting to seperate. After getting it in the basement and deciding where to start,, to my disappiontment,, the...
