I hope that this is the right place to post this question. I have a 1988 bayliner capri 19 ft. What I would like to know is how do you drain the gas tank. I was told that there might be water in the gas. <br /><br />thank you<br />Jim
HI what I like to no is in the fall I open the plugs and drain all the water from the engine ( OMC 3.0 COBRA ) I removed the hoses and flush out the engine.I closed all the plugs fill the engine connect all the hoses (2) back since the engine don't have a radiator how do I no if the engine is...
sorry its me again = is there a way you can bench test a trim gauge i dont have it hook up to the boat now as it reads now the gauge reads up on the back the 3 lugs are (s-sender) ( g-ground) ( I-ignition) how do they test them at the factory<br /><br />thanks for all the help <br /><br />Jim
is this the right place to post this im still new to this<br /><br />I have an OMC cobra stern drive 3.0 litre what I would like to no is there a special trim gauge I have to use for this drive I put a ( Faria gauge on ) but it does not work it don't move it just stays in the up position I try...
I have an OMC cobra stern drive 3.0 litre what I would like to no is there a special trim gauge I have to use for this drive I put a ( Faria gauge on ) but it does not work it don't move it just stays in the up position I try to check out the sending unit the 2 wires that come out I put the...
can the trim gauge works without the engine started or does the engine have to be runing and is there a way to check if the sending unit (brown/white) wire is working i have a 3.0 - OMC Cobra stern drive <br /><br />thanks jim :confused:
can the trim gauge works without the engine started or does the engine have to be runing and is there a way to check if the sending unit (brown/white) wire is working i have a 3.0 - omc Cobra stern drive <br /><br />thanks jim :confused:
can the trim gauge works without the engine started or does the engine have to be runing and is there a way to check if the sending unit (brown/white) wire is working i have a 3.0 - omc Cobra stern drive <br /><br />thanks jim :confused:
hi what i would like to no is -i have a 3.0 OMC Cobra i just drain the block and the water cool exhaust manifold now i want to put the antifreeze in when i was flushing the engine i did not see any water coming out of the block ( drain plugs are out for now )do i have to run the engine with the...
hi what i would like to no is -i have a 3.0 OMC Cobra i just drain the block and the water cool exhaust manifold now i want to put the antifreeze in when i was flushing the engine i did not see any water coming out of the block ( drain plugs are out for now )do i have to run the engine with the...
I have a 3.0 OMC Cobra 1988 and i would like to put a guage on to see where it is in the water,what are the parts i will need,and is there a wiring diagram is there a place on the web i can go to and are they hard to put on <br /><br />jim
is there a good solution to remove scratches on the paint on the hull like a wax or what kind of paint stick there are some really not deep<br /><br />jim
I have a 1988 bayliner capri does anyone know where I could find the color code for this type of blue. I need the paint so I could spray the exact color. <br /><br />thanks Jim
I just got a 1988 bayliner capri 20 footer it has a OMC Cobra motor and stern drive.what i like to no is the HP and what size the prop has to be = the prop i took off ( it busted ) is stamp on it is ( 13 3/4 x 15 ) the number is 391198 and it has 13 spline is this the right prop for this unit...
