Recent content by landyman

  1. L

    tohatsu 50hp workshop manual?

    lads is there anywhere that i can download a workshop manual for a 50hp tohatsu? thanks
  2. L

    seafoam observations!!

    i read on here a lot that of people reccomend seafoam for de-carbonising engines, in every thread without fail everyone reccomends mixing 10oz with a gallon of fresh fuel and run that gallon through the motor. nobody ever says wether you run the motor under load out on the water or that if you...
  3. L

    WOT revs??

    what should the revs at WOT be on a 70hp evinrude its a 2004 model 3cyl 2stroke, the proper one not a ficht or etec. i'm hitting 5900 at the moment which i think is too high.
  4. L

    150hp v6 suzuki mid 80's

    hopefully someone can help me out, a mate has a mid 80's suzuki v6, 150hp carbed model. was running perfect last season, went well first trip out this year then all of a sudden it lost a heap of power. we took the boat out of the water and started the engine on muffs and it sounded "off", carbs...
  5. L

    120hp evvy head scratcher

    its a 120hp v4 serial no bo120tlcm it will start up right away,idle rock steady for ever will get up and go like a scalded cat BUT if i turn off the motor after steaming out 6/8/10,miles it won't restart no matter what i try.if i l leave it over night it will start right up, idle rock steady and...
  6. L

    o2 sensor location 250hp ox66

    where is the o2 sensor located on the 250hp ox 66 motors?
  7. L

    yammy 70/90hp two stroke q's

    my 1998 70hp yammy 2 stroke has thrown a rod and i've been offered a 90hp yammy powerhead co-incidently from the same year. can i just unbolt the 70 and bolt the 90 in its place? or should i look for another 70 hp powerhead?
  8. L

    250 0x66 lh to rh conversion if poss

    mate of mine has just bent the propshaft on his 2006 250hp ox66 and as we are takin the box apart to replace it could we make it a rh instead of a lh rotation? the reason we ask is it is hard to find lh props round here. is it as simple as the gear on the end of the shaft or is it not worth...
  9. L

    1990 dt75 soozy

    can any one tell me the weight of the dt75? i am after buying one and need to get it shipped to me but the couriers need a weight. any help would be great as its sat on a pallet waiting to be collected!
  10. L

    100hp v4 suzook

    whats the story with the 100 hp v4 are they any good or do i run a mile from it?
  11. L

    merc 225/200 general question

    mate of mine is thinking of a getting a late 90's 200/225hp merc and was wondering what we/he have to look out for and what if anything to avoid? were any models better or worse than others etc etc any comments?
  12. L

    fixed jets 70hp evinrude

    after a bit of digging on the brp site i seem to have 1984 carbs on a 1989 engine which makes me think that the stalling when opening the throttles in gear is somewhat related the carbs are off a 75hp so i think the jets will be wrong question is what are the correct jets for a 89 70hp vro...
  13. L

    jets on 1989 70hp

    silly question lads but when i was looking at the carbs today i noticed that the jet on the side of the carb downstream of the butterfly was screwed in tight so checked all the rest and they are the same. would this cause the motor to stall/cut out when the throttle is opened under load? waht...
  14. L

    70hp evinrude 1989 probs

    got a slight problem with my 70hp 3 cylinder from 1989. it will start easily,tick over, run flat out all day long however it will go into gear ok no crunching but when you open the throttle to go it stalls to keep it going you have to put the choke in for a second then every thing is perfect. i...
  15. L

    piranha props

    lads i am after buying a piranha prop for my 70hp evinrude is a ny one else running them as the primary prop? are there any pitfalls any opinions any advice etc??
See more
Top