Current visitors

Home
Members

Mc Tool's latest activity

M

Mc Tool replied to the thread 1986 E70TLCDC Piston Destruction - What Causes This?.

Detonation ,its only done one cylinder , mostly adjacent to the exhaust port , which can rule out a few things. Poss lean running on...

Aug 15, 2026
M

Mc Tool replied to the thread Omc 4.3l won’t stay running after 60 sec.

So you can be 90% sure its not the pump , but its not the only thing involved in getting fuel into the motor . If you can check fuel...

Aug 15, 2026
M

Mc Tool replied to the thread 1980 110(9.8) hp Mercury outboard.

Leaking crank seals are likely to cause lean running and maybe loss of power but I dont believe they would completely stop the motor...

Aug 15, 2026
M

Mc Tool reacted to jimmbo's post in the thread XD100 Full Synthetic Light Amber Color with Like.

BRP's Official Literature Bans It from Non-DFI Engines From a parts counter, service department, and legal standpoint, XD100 is strictly...

Aug 15, 2026
M

Mc Tool replied to the thread How do I Remove Very stuck on Exhaust Manifold Gaskets?.

Paint scraper ....not to wide , maybe 1 inch and cut half the blade off to stiffen it up a bit and grind a bevel on one side ....like...

Aug 14, 2026
M

Mc Tool replied to the thread Vacuum line for Suzuki 2.5HP 4 stroke outboard.

Priest to the altar boy 😆

Aug 14, 2026
M

Mc Tool replied to the thread Vacuum line for Suzuki 2.5HP 4 stroke outboard.

Just push it a bit further into the hose ....or cut the hose to get it out and then stuff it into a new bit of hose if the old hose is...

Aug 14, 2026
M

Mc Tool reacted to Scott06's post in the thread Upgrade to 4bbl, what about throttle cable bracket? with Like.

Yes Pontiac called it tripower from 1959 to 1966 when they stopped making it

Aug 14, 2026
M

Mc Tool reacted to Berdink's post in the thread Sputtering Johnson V4 90hp - 1994 with Like.

In another thread I posted that my timing was way too retarded. I used the "Joe Reeves" method and set the timing at 23 degrees BTDC. It...

Aug 14, 2026
M

Mc Tool replied to the thread XD100 Full Synthetic Light Amber Color.

😁

Aug 14, 2026
M

Mc Tool replied to the thread rant.

Rock chips (12mm) and tar are NZ's go to for nearly all roads. Called chip seal , can be volcanic rock ( basalt or andesite ) or quartz...

Aug 14, 2026
M

Mc Tool replied to the thread Upgrade to 4bbl, what about throttle cable bracket?.

I recall Q jets being swapped out in favor of Hollies to cure "tuning " issues but I think the real truth was that few peeps here knew...

Aug 14, 2026
M

Mc Tool replied to the thread Upgrade to 4bbl, what about throttle cable bracket?.

Tripower? Is that what I would know as a 6 pack ,fitted to Mopar engines . Three x 2 bbl carbs ? 🙂

Aug 14, 2026
M

Mc Tool reacted to Scott Danforth's post in the thread Upgrade to 4bbl, what about throttle cable bracket? with Like.

I'm sitting here looking at my pile of holley carbs..... I'm not a fan of Edelbrock carbs

Aug 14, 2026
M

Mc Tool reacted to Bondo's post in the thread I can not believe with Like.

Ayuh,.... Not that I planned it, but all of my boats have flat glass windshields,.... So long as I can salvage the frame...

Aug 14, 2026

Show older items

Home
Members

Top