Where is the color sleeve for the Optical Sensor and the Stator located?<br />Manual states that original equipment was Black Sleeved and they were Warranty Repaired to be a Blue Sleeved stator and optical sensor.<br />Changed in 1993? To Gray sleeved.<br /><br />The wiring harness from the...
1992 150HP Evinrude with NO spark<br /><br />Went to OutboardRepair.com and reviewed their trouble shooting instructions as recommended in an earlier post.<br />
My engine has Black spark plug wires, Is it recommended to put new "gray" wires on the engine?
Twin 1992 Evenrude 150 HP, 6-cyl. 60° E150NXENC and E150EXEM Serial #s <br />PORT ENG: G03014951, STBD: G03076183<br /><br /><br />Counter-rotating engine has intermittent spark. <br />Background (sorry for being wordy) <br />I am still trying to get these engines running correctly. :(...
1992150 hp Evinrude<br /><br />Spayed corrosion block around starter solenoid, must have shorted out connections. Manual states that all connections should have OMC black dip applied, found all were bare/uncoated connections. :o <br /><br />Started engine, smoke from around starter...
I would like to bleed any air in my hydraulic steering, can it be done by one person?<br />I read this somewhere but I'm not sure I have it right. Does anyone know if this will work?<br /><br />Join the bleeder valves on the cylinder together with a hose<br /><br />open the bleeder valve on...
150 hp 1992 Evinrude,<br /><br />Just replaced the fuel / water filters on my new to me engines. Used original OMC housing with new Racor filters with the clear plastic bottoms.<br /><br />I did NOT fill the filters with gas before installing, just pumped the primer bulbs until firm. The...
150 hp 1992-Evinrude<br /><br />What is the correct position of the RED Primer Solenoid Valve lever?<br /><br />Twin engines, one has the valve lever straight down-vertical and the port engine is at 90°-horizontal. :confused: :confused: <br /><br />In the manual it explains how to...
>>>Any recommendations on how to bleed the steering system (there are bleeding Ts on the sea star cylinder/ram)? <br />Do I turn on the Autopilot prior to bleeding the SeaStar steering?<br /><br />The hydraulic fluid in the helm pump is low, filled the fluid and will need to bleed air from...
Sorry for asking a dumb question.<br />1992- 150hp Evinrude, engines are new to me. <br /><br />I want to change the lower unit fluid and cannot get the plugs out. <br /><br />Tried a hand held impact tool, broke the screwdriver bit.<br /><br />Put some PB Blaster, no help. bought the bigest...
In another post they recommended going to this site for information on charging systems: outboardparts.com <br /><br />Why do they recommend not to use Maintenance Free Batteries? How will the battery blow the packs? :confused: :confused: I have 2-brand new Maintenance Free, shall I...
I posted this earlier this evening but it disappeared from the forum I hope I didnt violate any rules etc.<br /><br />Well Im no longer a boatwantabe, bought one yesterday and need you help. The boat has twin Evinrude 150s, Model E150NXENC, E150EXEM---unreadable , serial numbers GO3076183...
Does anyone know the type and year of these engines. (Or a web address where I can look it up?)<br />PORT ENG: G03014951 <br />STBD: G03076183<br />Both are 150 hp Evinrudes I believe they are 1991 but not sure, <br /><br />Thanks<br />Mike
Hi All,<br /><br />I am making progress with purchasing a boat. Thanks to all of your help I have avoided several blunders.<br />I put a deposit on a boat with twin Evinrude 150 hp. 1991 mfg. date (rebuilt in 1997). Could anyone tell me what the RPM should read at WOT during the sea trial? Im...
Last week I put a deposit on a 1986 25 Boston Whaler Outrage with twin Evinrude 150s (1991 rebuilt in 1997). The purchase is pending results of compression check as well as a mechanics written evaluation of the engines and a sea trial. What should I look for during the sea trial? <br />All...
Well, Im still searching for a boat! Thought I found a deal with a 150 Force and was going to purchase even after reading all the bad along with the good comments on Force engines, but the seller refused to allow a sea trial or even to start it with ears in the driveway. It wasnt that good...
