MNhunter1's latest activity

  • MNhunter1
    MNhunter1 replied to the thread 1972 Starcraft Nova.
    My Nova was a 15ft, so I was able to cut them from an 8ft sheet. If you can't fit them diagonal to get them out of an 8ft sheet, I'd...
    • 100.JPG
    • 101.jpg
    • 144.jpg
  • MNhunter1
    MNhunter1 replied to the thread '77 Holiday Transom.
    I typically use the US Composites 635 thin with the 3:1 ratio medium hardener. I paint the exposed side after the epoxy cures.
  • MNhunter1
    MNhunter1 replied to the thread '77 Holiday Transom.
    Yes, and encapsulate with a 2 part epoxy. I generally use 3/4" ACX plywood from the big box stores.
    • 092.JPG
    • 093.JPG
    • 095.JPG
    • 096.jpg
  • MNhunter1
    MNhunter1 reacted to N1265's post in the thread '77 Holiday Transom with Like Like.
    2 sheets of 3/4 glued together ?
  • MNhunter1
    MNhunter1 replied to the thread 1972 Starcraft Jupiter New Project.
    • 099.JPG
    • 100.JPG
    • 101.jpg
    • 119.jpg
    • 130.JPG
    • 143.JPG
    • 144.jpg
  • MNhunter1
    MNhunter1 replied to the thread 1972 Starcraft Jupiter New Project.
    The side panels are screwed to the floor, riveted to the inside tray (about halfway up the panel/likely behind that trim?), riveted to...
  • MNhunter1
    MNhunter1 replied to the thread 1973 StarCraft SS 16 Restore.
    Each rib. You can see where the original holes were from the factory. I always go through and remove and replace all the rivets...
  • MNhunter1
    MNhunter1 replied to the thread 1973 StarCraft SS 16 Restore.
    That's a first for me, and rather strange. Not even sure what they were trying to accomplish, but it does look intentional. The good...
  • MNhunter1
    MNhunter1 replied to the thread 1973 StarCraft SS 16 Restore.
    My first step on a gut job is usually always to remove the motor, but I guess it's just personal preference. If you have the stand, I'd...
  • MNhunter1
    MNhunter1 replied to the thread Transom Reinforcement.
    With a solid transom, knee brace, splashwell, decking, and respective factory bracing which tends to vary from model to model, you...
  • MNhunter1
    MNhunter1 reacted to Pmt133's post in the thread Boat Cover with Like Like.
    I recently tried the carver sundura. It does leak slightly... mostly at the seams and even at that I'm talking a teaspoon of water after...
  • MNhunter1
    MNhunter1 reacted to FLATHEAD's post in the thread Boat Cover with Like Like.
    My last two boats I bought Carver Sundura covers. They have held up very well. My boat sits out all spring, summer, and fall. I store it...
  • MNhunter1
    MNhunter1 reacted to airshot's post in the thread Boat Cover with Like Like.
    If you are going to trailer with the cover on, then get a custom made cover....costly yes, but they will last far longer. Already made...
  • MNhunter1
    MNhunter1 posted the thread Boat Cover in Starcraft Boats.
    Keeping this in the Starcraft forum as I'm primarily interested in feedback on these old hulls. Looking for a cover for my MR180. It...
  • MNhunter1
    MNhunter1 replied to the thread Tiller Main Motor.
    It all depends on how you mount the kicker. A lot of kickers are short shaft motors, but you can find them pretty easily in a long shaft...
Show older items
Top