Recent content by mr gibbs2

  1. mr gibbs2

    remote oil tank gauge

    hello i have a remote oil tank for a 200 hp evinrude year 2000 system check , really can't see the tank oil level by looking at it ,it has a remote fill . Don't want to fill it up to the filler tube top it may leek. can i run a gauge off the wiring harness to monitor oil level in the tank...
  2. mr gibbs2

    ox66 LOW pressure pumps leaking

    when testing LP pumps 1 undolt them from motor 2 squeeze primer bulb . result// seems gas is leaking out of the mounting holes to the pumps , not out of the hole that goes to block . Question Does the mounting holes have to be bolted together to do this test . motor bogs down at 3800 rpm ...
  3. mr gibbs2

    2001 ox66 250 sneezing

    fuel pressure 38 at idle today stays steady . last season change all filters, had injectors cleaned lift pumps replaced ran well last year. did not drain vst for winter . first time out runs poorly , sneezing stalls surges up then down and stalls , smokey , sent injectors out today for service...
  4. mr gibbs2

    2001 250 ox66 fuel issues

    I can here pump on and tank fills when I crank or when pump ball , and fires when I spray gas with oil into throttle body but no pressure on reading on gauge even with the valve removed, it only comes out at a dribble
  5. mr gibbs2

    250 ox66 2001 running poorly

    Was running rough , now not running . last Season replaced all 3 pumps all filters I can here pump on and tank fills when I crank or when pump ball , and fires when I spray gas with oil into throttle body but no pressure on reading on gauge even with the valve removed, it only comes out at a...
  6. mr gibbs2

    is the motor to low?

    is the motor to low ,im thinking one more hole up !
  7. mr gibbs2

    Crap on transom cracked

    Transom picks new project 1997 stratos 2100 center console going to repower with a newer motor . Took motor off and inspected holes all wood or what ever it is made of I don’t , no water intrusion can’t scrap anything out of it its hard , it after taking the aluminum trim plate it has a crack...
  8. mr gibbs2

    2002 250 ox66 compression

    thinking of buying a 2002 ox66 250 hp yamha getting out of the late 90s evinrude loopers . i found a motor with compression at 120 on all 6 cylinders tested my me with my gauge always on the money, the motor starts, runs good on the stand , unknown hours , no gauges . my question is , is...
  9. mr gibbs2

    timing v6 evi rude

    1990 200 hp evinrude . replaced power pack, timer base , sator,with digital cdi units ,and replaced flywheel . Runs as good as it always had before power pack went south , but starts at the flip of the key . top rpm is 5300 no hesitation but timing is off about 8 degrees with a test wheel in the...
  10. mr gibbs2

    Flywheel inner magnet

    1990 v 6 looper 200 Hp testing done with s Stevens cd77 evinrude not getting and volts out of port side of timer base , would a bad inner magnet only have voltage on one side ,the starboard side has volatage when cranking port none, is it the timing base or the flywheel
  11. mr gibbs2

    TIMER BASE SENSOR COIL TEST RESOULTS

    1990 200 HP EVINRUDE no spark now has been acting up , now no spark. output test using stevenes 77 neg on the port middle terminal . then red lead to the remaining posts. i get voltage on only one post while cranking motor all other nothing .the does that mean the timer base has failed sator...
  12. mr gibbs2

    Hydra sports,transom

    Just picked up my old 86 Hydrasports vector from the person I sold it to years ago ,as a project .it was a great boat. however I know the transom is de laminating on one side it's wet . , there is no flex or cracks but it been wet many years as a result of how the live well fitting was...
  13. mr gibbs2

    Older rubber hub ss viper prop on newer v6

    Hello all ! have a very nice older viper prop that I want to put on my 2001 Johnson 200 hp v6 .the aluminum prop on it now has the newer hub system and the thrust bushing dosent push out the viper prop enough to turn free . Is there a trust bushing that would allow me to use this prop thanks.
  14. mr gibbs2

    Re core gunell

    Re cored gunnel and and having a tuff time Finishing it off . Are there any tricks to using epoxy over head ? I can't seem to get it to tack and stick and making a mess . I'm using west system slow hardener . the repair is solid but I would like to make it look good . I recorded it with 1/2...
  15. mr gibbs2

    Rotted core under acess plates

    I was going to caulk under acess plates and when i took it apart , not good the area is bumped out underneath about 1 foot by 18 in and stops on all 4 sides . I've cleaned out almost all that is damaged and cleaned it with actone and will rough it up wit sand paper . Any recommendations on...
See more
Top