I have just replaced my 11x9 prop with a 10.5x11 prop on a 35 hp evinrude. now it makes a whining noise at certain rpms. the performance works out for me but is this going to hurt anything in the long run and is there any way i can get it to stop whining? Or could it be the drivetrain making the...
I have a 1976 35 hp evinrude. I started hearing a sqealing noise when throttling down or up sometimes but always when coming down off a plane. I'm worried it is a bearing sqealing. Now the parts manual shows the oil recirculation hose going from the lower crank bearing to the upper crank...
I am wondering if the flywheels on a 1976 35 hp evinrude are interchangeable. I have the rope start model and found an electric start flywheel. It looks like it would work because it has all the rope start grooves and everything. To me they look indentical other than one has teeth. If anyone...
Looking for a salvage yard in the upstate around the Greenville or Anderson SC area. If anybody knows where one is and can help me that would be great. Thanks
hey guys I sheared a flywheel key and cracked the flywheel. Im looking for a boat salvage yard around the Anderson SC area or the upstate area in South Carolina. I keep hearing about some salvage yard up here but nobody can find it. If anybody can help me out that would be great. Thanks.
well i sheared my flywheel key on my 1976 35 hp evinrude rope start. the flywheel is junk because it cracked it but i think i can clean up the crankshaft and make it work but its not to pretty. does anybody know of a boat junk yard or something that might have a flywheel for me?
I just have a question because my service manual depicts two different pictures that show the oil recirculation hoses routed different. It is a 1976 35 hp evinrude rope start. The way I have it hooked up is the hose going from the top crankshaft bearing is going to the lower crankshaft bearing...
i have a 1976 35 hp evinrude and the top cyl is fouling and not running on it at all because when i pull the plug wire it does nothing and when i pull the bottom it dies instantly. So the compression is 120 psi on both cyl, the spark will jump an easy 1/4 inch on both cyl, the point gap is...
i have a 1976 35 hp evinrude rope start. both cylinders have great spark being i just put new electrical everything on it. they jump a 1/4 inch easy. but when i start it, it is only running on the bottom cyl. i don't think fuel is an issue because the bottom cyl has plenty of it. but when i pull...
This is a 1976 35 hp evinrude. I have this oil coming from this hole in the lower unit and its engine oil. There is also oil coming out of the exhaust also unburnt engine oil. my first question is what is that little hole for and second does this just mean it is not burning all the fuel mixture...
I am adjusting my timing and before i do that i need to set the full throttle stop. The stop got turned while rebuilding the engine and my question is that, is there any way to adjust this stop without running it at full throttle because i do not have a tank and it would have to be out on the...
I have no spark at all on either cylinder and have checked everything the book says and it looks ok as far as a regular ohm meter will tell me. I did notice that the driver coil under the flywheel the center coil is shorted to the other posts that are beside it that the screws go through. That...
I have a 1976 35 hp evinrude and when i run the engine water comes out of the two cooling holes up top just fine. But it also comes out of the two holes right behind the steering collar on the exhaust housing. wondering if tho is right?
i just have a question about the leaf valves on my 1976 35 hp evinrude. the manual is very clear about the leaf valves needing to have a perfect seal and not to damage them. my question is that if the leaf valves do not seal perfectly would that make the engine run to lean of to rich?
I have a 1976 35 hp evinrude model 35602S and have just rebuilt the powerhead by boring the cylinders .030 over and new oversized pistons and rings. Along with all new gaskets and seals. It had horrible compression before in the 30's to 40's, cause it sat for a really long time and the cylinders...
