Recent content by NeWcS

  1. N

    Question(s) about replacing the foam/floor in my deep-v

    So I took the majority of the back floor out and have to say I was pretty disappointed. I was expecting/hoping to find 200lbs+ of water-soaked foam. I didn't. All the foam looks good and had only a few spots where the foam was holding water. There was only a little bit of water in the hull. I am...
  2. N

    Question(s) about replacing the foam/floor in my deep-v

    I did some work on it today. I took the laminate flooring off the deck. The wood looks in pretty good shape. My only fear is that there is an aluminum deck under the wood floor. When I took the seat mounts out, I can see there is a sheet of aluminum under the wood. I am hoping it's just part of...
  3. N

    Question(s) about replacing the foam/floor in my deep-v

    Thanks! My boat is actually better than that in the picture as mine has a 75hp. lol. Thing is a little rocket-ship. Man, I don't even know where to start. I guess I could pull off the laminate flooring and see what I see. heres mine:
  4. N

    Question(s) about replacing the foam/floor in my deep-v

    In terms of removing the floor; what should I expect? Will it be screwed down to some supports in the hull or will I need to expect to have to cut it out? I know every boat is different, but what is typical for this style of boat. This is the make and model of what I am working with. 2001...
  5. N

    Question(s) about replacing the foam/floor in my deep-v

    Once I work up the nerve to start cutting, I'll post some pics.
  6. N

    Question(s) about replacing the foam/floor in my deep-v

    The foam is rated in lbs/density. What am I wanting as far as that goes? thx for the help!
  7. N

    Question(s) about replacing the foam/floor in my deep-v

    Thanks for the reply! It's an aluminum boat. Not sure on the weight. I know the motor (75hp Merc) weights about 300 lbs. I'd guess the boat is less than 1000 lbs. So you put the new floor in then pour the foam? Or am I misunderstanding?
  8. N

    Question(s) about replacing the foam/floor in my deep-v

    So for the past few years I have noticed that my boat has been sitting really low in the water, in the back. After doing some research and talking to a few people; it turns out the foam may be waterlogged. Well today I took out one of the seat mounts and was able to get to a small piece of the...
  9. N

    Issues after impeller change. Gears seem off. Pee's fine now

    2001 75hp ELPTO So I changed the impeller on my outboard and think I have an issue. I put the motor in forward before removing the 5 nuts. Took the lower unit off and replaced the impeller and gaskets from a kit I bought., Had a hell of a time getting the unit back on. Put the shifter into...
  10. N

    Question on starting an outboard. And fuel line question(s)

    Good idea'r, Thanks!
  11. N

    Question on starting an outboard. And fuel line question(s)

    Unfortunately there are no markings on either the dial or on the handle grip.
  12. N

    Question on starting an outboard. And fuel line question(s)

    Thanks for the reply and info! I went ahead and ordered a new impeller. Thanks for that.
  13. N

    Question on starting an outboard. And fuel line question(s)

    So I just picked up a 1973 Johnson 20R73A 20 hp and had a question on how to start it. I'm pretty sure I know how but need a refresh. What do I set this dial to? And what is it's purpose? I assume I pull the choke till the motor starts than close it. Right? Also, do I turn the throttle...
  14. N

    2001 75hp - Sparkplug gap, fuel filter, RPM info needed

    Hi can anyone help me find these things? Looking for spark plug gap and plug recommendations. Part number to replace the fuel filter. And what the optimum RPMs to run at. ser# 0t300451 - 75elpto - Mercury Thank you
  15. N

    How to avoid carbon buildup in an outboard?

    So the first kicker motor I had a couple years ago go all jacked up due to carbon build up. After speaking with the guys at a shop about it I was told it was due to the fact that the motor was always running at really low speeds/rpms which causes such build up. So aside from running it at W.O.T...
See more
Top