Recent content by noworries79

  1. noworries79

    5 Wire Flat to 6 Wires?

    Re: 5 Wire Flat to 6 Wires? Thanks for the replies. Here is what I have like posted above. I am going to have to spend some time figuring this thing out. I am missing out on my fishing time!
  2. noworries79

    5 Wire Flat to 6 Wires?

    I have partially installed my new wire harness and I have a brown/green and brown/yellow that needs somewhere to attach (from trailer). My new harness only has 5 wires (green, yellow, brown, white and blue). Is it possible to attach both brown/green and brown/yellow to brown with a heat shrink...
  3. noworries79

    show us your fish

    Re: show us your fish My Brother's first sail, he looks excited!
  4. noworries79

    Caliper question

    I was going to bleed my breaks the other day when I realized that my left, rear caliper had no break line attached!!!:confused: I have a 2007 venture double axle trailer and I didn't notice this problem before. I may have done a few trips without the break line attached. I took the caliper...
  5. noworries79

    Hey boys...

    It's been a long time since I have posted. How the heck are you folks and how have you been beating the heat? I just got a new-to-me Key West 2020WA and we are running her like we stole it! Ha ha :D
  6. noworries79

    1992 Evinrude 48 SPL manual trim lock not engaging

    Recently I realized that the lever lock that releases and locks the engine doesn't lock into place. I have tried to disconnect the cable with no luck. Any ideas on where to start? Thank you in advance.
  7. noworries79

    Evinrude 48 SPL lower unit plug

    I am going to change the lower unit oil soon and I was wondering if this engine model should have the washer replaced each time the lower unit oil is changed? I have not drianed it yet, I am just trying to get everything I need before hand. Also, I have purchased the Quicksilver Marine...
  8. noworries79

    How to lube your steering shaft?

    Hello all, I am having a tough time with my 1993 Evinrude 48 SPL. I can't get my steering cable nut off of the shaft area so I can clean/lube it. My steering has been very tight lately and all I have been able to do so far is turn the wheel, clean as much of the shaft as I can, then turn the...
  9. noworries79

    Bearing friction

    Hello all, I have just replaced my bearings on my 16 foot boat trailer and I am still hearing a little friction. It is almost a slight grinding sound. This is the reason I decided to replace them in the first place. After the installation, the driver side seems fine, but the passenger side...
  10. noworries79

    Sticky gelcoat

    Do you know of anything I can do about my tacky gelcoat? Overall I am happy with how it looks and how the non-skid feels, but there are a few tacky spots that don't seem to be curing. Any ideas?
  11. noworries79

    Today was a good day

    Finally making headway again with the restore. Got the deck glassed in and I can almost smell the salt creeks again! I am ready to fish and the fishing machine is a gel coat away from being there. I can't tell you how good it feels to be at this stage, but then again alot of you have been...
  12. noworries79

    Glassing a livewell

    Does anyone have any experience with glassing a livewell to the underside of the deck? I have a 25, maybe 30 gallon livewell and I am worried about the weight issue. Will 1.5 oz. CSM and 10 oz. cloth be sufficient? Thank you in advance!
  13. noworries79

    Quick deck glassing question...

    Hi Everyone, I have been racing through my resin supply using CSM for stringers & bulkheads. When I eventually coat the top surface of the deck do I need to wet out the CSM before the cloth? Can I wet the plywood, lay out the CSM and cloth then wet both from the top? I know this is a newby...
  14. noworries79

    Livewell questions

    Hi everyone, I have a 25-30 gal. livewell that needs to be glassed on to the underside of my casting deck. I haven't installed the deck yet, so I plan on glassing it before hand of course. I only have 1.5oz CSM and 10oz. cloth, and my issue is securing the livewell enough so it will stay put...
  15. noworries79

    Best method for leveling stringers/deck

    I have a concern about my re-construction, my hull isn't exactly symetrical (imagine that) Ha ha. My stringers are cut to fit but they are not level. Should I tab them in, then do a cut to the top of them? I ask because we started cutting the previous stringers and ended up too short. There...
See more
Top