Recent content by P2

  1. P

    suzuki df9.9a Hard start. No run

    I use this df9.9a I believe its a 2014. last year of the carb .as an aux or trolling motor. It never started or ran well. Shop I bought from stopped serviceing them right after I bought it. Found another and they said its bad gas. I am quite particular with my fuel. Always treated and filtered...
  2. P

    1998 Honda bf9.9 no spark.

    Hi there, I have a 98 honda 9.9 that has no spark. I have disconnected the kill switch and still no spark. I have not picked a manual up yet so would appreciate some steps to sart with. Babl 1204405. Thanks
  3. P

    98 s150txrw. troubles.

    I have a s150txrw bracket mounted on a 19 foot cuddy. I bought just over a year ago as a used rebuilt . It then started acting up on accelleration out of the hole. I believed this to be fuel related and have rebuilt the carbs and replaced both thermostats and fuel pumps .Everything is set to...
  4. P

    Plastic Carb roller ( accelerater cam to Carb )

    Hi guy's. I have a 1998 s150txrw' Carbed. My plastic roller has a flat worn on it and needs replacing. My Yammaha dealer is having alot of trouble finding the part # for it. Anyone come accross this already? It rides on the shaft of the middle carb and rolls against the accelerater cam ...
  5. P

    1998 s150txrw yamaha link & sync?

    Ok I'm now going to try to fix my next issue. When accellerating slowly it seems to have some sluggishness and bogging down, This is greater if I accellerate quickly.This s150 is carbed and has a choke . The Carbs are off a 200 hp. The center carb is correctly linked to carbs above and below.I...
  6. P

    Yamaha instrument problem.

    I have mounted a 1998 s150txrw on my 19' Calais. On a pod. It is replaceing a 1990 200 etxd. I had bought the required connectors to work with this year of engine. Things have gone ok untill one day I started looseing my Tac. ( Yamaha lcd ). Just faded in and out till gone. A couple days later I...
  7. P

    Yamaha wireing differences, 1990 vs 1998

    My 1990 200 etxd unfortunatly had a nasty old 6208 bottom bearing I wasnt aware of untill it went Bang!. That being said , I was able to pu a 1998 s150txrw in great shape cheaper than repairing the 200. I have wireing harness differences though. 10 pin is the same. The 98 has a 4-pin that...
  8. P

    Hey Rodbolt,Can get pump running with emerg. switch now but not automatic.

    Hi there. I Have an issue with the oil transfer from the remote tank to the engine main tank. 1990 200 etxd. I have searched the forums and found very helpfull info. Did the regular checks/tests of sensors and found the trim/tilt sensor out of spec. Thought I had her licked till I just recieved...
  9. P

    Yamaha timing plate

    Hi there. I have a 200etxd. I picked up a seloc manual to give my timing a look at. Maybe I should have spent the bucks and bought a yammy one lol.I followed the instructions in the manual over and over. .012 before tdc from # 1 cylinder. Timing pointer reads 6 to 7 degree's. If I follow the...
  10. P

    200 hp yamaha- Need cable

    Hi guys, I need a cowling release cable #6R3-42850-00-00. And a pipe #6G5-43833-00-00 ( for power tilt)Any of you parts guys have new one's in stock?? I used a metric brake line for a couple years but the salt water is harsh lol. 200 etxd. Thanks guys.
  11. P

    1991 Calais cuddy , Anyone have information for a BC made 19" calais.

    I have a 19' made in BC Canada calais cuddy. I run a 200 Yamaha mounted on a external bracket. I have no idea what this boat is originaly supposed to weigh. Any info would be great TX
  12. P

    Rust stains in gelcoat

    Hi Does anyone have any suggestions for removing rust stains from a gelcoat surface?? TX
  13. P

    Caulking

    Hi I have just removed and cleaned my under deck fuel tank. I now have to reseal the Deck cover. I removed as much of the old caulking as i could but theres still a lot left. Can some one suggest the best solvent for this job. Thanks
  14. P

    Fuel

    Have just got back from a fish'n trip that while cruising back to camp I lost all power. While troubleshooting I found that no fuel was passing to the motors. Checked the fuel/water seperator and Have what looks like a clear silicon gell blocking the filter. It also plugged the fuel supply line...
  15. P

    200 hp Yamaha is sick.

    My 1990/91 200etxd is acting up. I have done a compression test and all cylinders are good. I made a spark tester and all cylinders seem to spark but dont know how good. ( can I measure this?) I replaced the fuel filter/ water seperator and spark plugs this spring. Problem started with a...
See more
Top