Recent content by ridnlow

  1. R

    Honda BF200 Purchase ?

    HI all, well I have been searching around and I am in the market to purchase a Honda 200 outboard 25" shaft. Just searching around seeing if any dealers have one in their stock on sale :) Or if anyone here knows some good prices of ones ? I have found so far best price of $15,400. Thanks
  2. R

    2001 FICHT 175, trying to sort issues

    Hi all, well my 175 FICHT Evinrude has always run good . I have had throttle response issus for a little bit but she still ran ok. When I go to engage forward its some what hesitant, and then I throw her to full throttle and my engine seems to slowely increase in rpms then get up to a max of...
  3. R

    DFI Technologies still open???

    Anyone know if they are still open? I have tried to call all day, and sent an email but it was returned.
  4. R

    Evinrude, ecu codes, 81, 82, 84 etc, coil packs

    Hi all, I am getting check engine light on my 2000 175 FICHT, and codes are 81, 82 etc, all 6 coil packs, it is saying not working properly, I am sure all 6 did not go bad at once, I read on another forum possible ecu/emm replacement, anything else to check first before I go this route, I do...
  5. R

    Evindrude FICHT, Code retrival process???

    Hi all, I read in a post before you can get the codes out of the check engine light, but disconnecting the throttle cables and opening the throttle to WOT and then turn the key on and the check engine light will blink out the codes? I guess this is not the correct way as I have done it several...
  6. R

    92 Yamaha 250, looking to buy questions?

    HI all, I am looking into buying a 92 VX76 Yamaha 250. I have been told it runs great, has great compression etc, anything else to look out for? Can the oil tank be eliminated on these for precautionary reasons?
  7. R

    Max RPM on 2000 175 Ficht?

    Hi everyone, just curious on what rpm range I should be running on my 2000 175 ficht? it has Viper 14.5 X 19 prop on it, I have been running about 4000 rpm's as of now not sure where I should not go over. Thanks
  8. R

    1999 Yamaha 200 powerhead rebuild ??'s

    I am looking to purchase a 99 Yamaha 200 with blown powerhead, just curious on rebuild pricing, and any step by step for DIY mechanic's? Also any tips help etc Thanks
  9. R

    2000 Ficht 175 proper first time startup ?

    Hi all ,just curious, I finally got my engine rigged and covers painted and boat almost done. Anyhow, I am wanting to make sure I prime it all correctly etc, I heard from a BRP guy that you have to make sure and hold the return oil line clamped down/crushed to ensure proper oil priming, is this...
  10. R

    Need console door/hatchs for center console

    Hi all, I am in search of either 2 17"X17" hatch/doors for my console or one 17"X34.5 " double door setup for access to under my center console. Thanks for any help.
  11. R

    Looking for 21 ft Cobia hull for project

    HI all, looking for a 21ft Cobia hull for a project boat, prefer 2000 and newer. Thanks
  12. R

    TO all who want factory oem decals cheap!!!

    Hi all, i just was searching around for replacement factory decals, the local dealer said $172.00, tried to find online they wanted like $99.00 to $129.00 for aftermarket look a likes, then I called Shorts Marine I purchased before a bunch of oem BRP evinrude stuff, they gave me pricing of...
  13. R

    Best place to buy factory evinrude decals?

    Hi all, I have a 2000 Evinrude FICHT 175, am and looking to get a new set of factory loooking decals, as I have just gotten the motor comoplete painted and looking new. The local dealer wants $180.00 for a set. Thanks
  14. R

    Gel coat diamond pattern??

    Hi all, just curious, I am wanting to get some gel coat work done on the floor of my boat, but it has a diamond pattern in the floor of the gel coat. Is there a template or a some way to do it to get it to look close to factory diamond pattern? Thanks
  15. R

    Gel coat diamond pattern?

    Hi all, just curious, I am wanting to get some gel coat work done on the floor of my boat, but it has a diamond pattern in the floor of the gel coat. Is there a template or a some way to do it to get it to look close to factory diamond pattern? Thanks
See more
Top