Recent content by rjcamel2355

  1. R

    1999 200HP OX66 surging/cutting out

    I was thinking possibly the pressure regulator too, I'll pop the VST open in the next day or so and make sure everything looks clean. I did notice that once or twice when I turned the key to on, I didn't hear the HP pump kick on, but I could have just not been listening close enough.
  2. R

    1999 200HP OX66 surging/cutting out

    Never cleaned the injectors, planned to a couple years ago, but it was running fine so I didn't want to mess anything up. Will hook up a fuel pressure gauge next time I take it out to run it, it would rev fine in neutral, but I understand that free revving vs running with a load is entirely...
  3. R

    1999 200HP OX66 surging/cutting out

    Hey folks, I have a 99 model 200HP 3.1L ox66 yamaha outboard, motor has ran awesome for the past 5 years, took it out saturday and if I ease into the throttle and keep it under 1/3 throttle itll run and drive all day. If i try to floor it or push it over that point it'll fall on its face, and if...
  4. R

    1992 evinrude spark issues

    Hey folks I have a 1992 evinrude 200hp xp model# ve200slens I thought I had no spark, pulled all the plugs and I have spark on cylinder #4 that's it. I've disconnected the red plug,no change. I've disconnected both kill wires no change starter turns the motor over healthily compression is...
  5. R

    Skeeter top cap decals

    Hey guys I have a skeeter zx202c, I lost one of my decals off the side of the boat and I am looking to replace them. I'm not sure where i can get the raised domed oval decal, but i have considered using a skeeter sticker instead. Anyone have any pictures of their boats with decals or logos on...
  6. R

    1976 55hp johnson dies when put in gear

    Hey guys I've gotta 1976 55hp Johnson motor, 2 cylinder with great spark to both plugs. I've tried different tanks. And this has me at my wits end. I can start the motor and itll idle all day long, but when put into gear it falls on its face and dies, only way I've been able to keep it going...
  7. R

    Carpet alternatives?

    Hey guys. I've got a 1999 skeeter zx202c. I don't bass fish and my carpet always ends up covered in fish slime (catfishing) what would be some good alternatives when I go to replace it, or should I just stick to carpet?
  8. R

    Bad day.....broken ox66 3.1l

    Hey guys, had a bad day yesterday boat jumped the chocks when I was unlocking it from the truck. Rolled down the hill into a fence, broke a few things scratched up my cowl and midsection a bit. Busted one fin on the side of the lower also.... I can not seem to find this steering arm..... any...
  9. R

    1998 19' Challenger Center Console (Seat Question?)

    Hey folks, I stumbled upon a 1998 Challenger by Kencraft? it's a 19' center console, with a 150 XR6 on it. Going to look at it this weekend, my question is this.... The "Back rest?" that you would lean back against on the front of the console is missing, is there a place I can order that piece...
  10. R

    1997 50tlhv Yamaha carb adjustment

    Hey guys, got a 1997 50hp yamaha that I need to adjust the carbs on, before I got it it had a someone messing with all the linkages and screws. Got the carbs cleaned and linkages lined out, but it's idling really high, it's got a screw in each carb. Could anyone give me an idea where to start...
  11. R

    3.1L ox66 Squeak

    Hey folks, Just started noticing a "squeak/squeal?" sort of sound from my 200 3.1L OX66 1999 model, seems to be more apparent in gear, can't really hear it at WOT, but at idle it's very noticeable, doesn't seem to do it at the beginning of the trip..... It seems to show up after running it for...
  12. R

    1982 150hp blackmax powerhead swap issues

    Hey folks, I picked up a used powerhead to swap onto my midsection, checked compression and spark 120PSI on all 6, spark on all 6. Got the motor onto my midsection, and bolted on. Swapped known good carbs, and powerpacks onto the engine. Put it onto the hose, fired it up sat there and idled...
  13. R

    1986 Yamaha 200hp Idles high.

    That should be touching at idle, as that controls the acceleration, as you can see it's not touching. That's the cause of your high idle. That's what I was getting at earlier.
  14. R

    Difference in these two props?

    I'm looking at a solas 4blade prop to run on my 3.1L yamaha, just to pull tubes/ski's. Looking at the 23P Amita 4. There is a Mercury Version, and a Yamaha Version. Am I incorrect in thinking that Yamaha and Mercury have interchangeable props? I know I have personally ran my old 21P Solas on...
  15. R

    200hp 3Ox66 rpm loss

    Hey folks, got a 1999 3.1l ox66 200hp efi engine. It hasn't gave me any major issues to date. However I got on the lake today and noticed about a 6-800 rpm loss at wot, about 8mph on the top end. Got home checked the compression, 110 across the board on my China made gauge (same compression as...
See more
Top