Recent content by rost495

  1. R

    1967 E parts?

    A friend has what we think is a 67, 9.5 Evinrude. According to him a piece is broken off the fuel pump, where the line goes in, and it leaks. Any chance of finding that part? If so where? I did a parts search here and come up with nothing. Thanks, Jeff
  2. R

    03 25 yamaha 4 stroke, Kill Switch won't work

    The old one started not working off and on. Assumed it was going bad, bought a new factory one, wanted to use the boat Saturday, the new one won't kill it either. WTF is going on? White wire touched to motor block won't kill it. Took ground off again and made sure I had nice shiny...
  3. R

    Kill Switch Won't Work? 25 Yamaha

    I don't have the motor with me currently, IE no serial number or year date, IIRC it was bought new in 2003.. book was printed in 2002... Model F25MHB 25 horse 4 stroke. I had recurring carb issues, no high speed or big lag.. anyway think I have that cleaned out with crud in the carb, along...
  4. R

    Hull Hook Question, RE boat hull - please read

    A bit off topic... This sight has helped so much on a restoration, that I thought I'd toss this out. I just bought a used airboat. Glass hull. The hulls have UHMW called poly bolted to the bottom, about 700 bolts. Its to protect from rocks, gravel, sand, etc... IE the bottom, mostly while...
  5. R

    95 200 Johnson Tach and trailer loading ?

    2 seperate questions. First, I have a tach, its on old boat and used motor. I have the sender wire running to the engine but have not made time to find out which wire to connect it too.... I ran the boat and motor in the lake for the very first trial run today. Noticed the tach works...
  6. R

    Need to Tighten Flywheel nut with ???

    I know the flywheel nut is 1 and 7/16 inch on my motor, 200 Johnson 95. Only thing is all the sockets we have are to thick of a wall to get in there. Is this one of those 100 dollar sockets I'm just gonna have to buy or what? THanks, Jeff
  7. R

    95/200 Johnson- Electric Fuel Primer

    I've ohmed out my selanoid, it appears bad, teh circuit shows positive voltage so it seems good. Motor wouldn't run long or rev up without dying. Manually flipped the red lever(it moves over 180 degrees...) and it would run and rev up. I need to replace the part, plus the seals/orings, it...
  8. R

    1993/94 200 Johnson Ocean Runner water tube?

    Never had a motor this big. Comes across as a 93, but serial number search shows 94.... Anyway bought it a few years back, and due to family issues it sat. Started it yesterday, almost instantly. I was amazed. But no pee hole on a big engine? I don't see one. Need to know how I know if its...
  9. R

    Temp Sending Units??? What kind?

    Have a 94 Johnson Ocean Runner, 200hp. I have a teleflex gauge (its a pieced together boat so bear with me) and the motor above is new to the boat. It has a hole half into the head on each side, tapped but not into the actual motor, just dead ends, just like the overheat guage hole. Problem...
  10. R

    power from key switch

    Getting it all worked out... dawns on me there is no need for fuel, tach, temp, gauges to run while the motor is off, IE draw current. I was going to connect to a fuse block with master off, but now it seems I should find a fuse protected circuit somehow but controlled by the switch only. I'll...
  11. R

    200 Johnson, 94, Tach Wire?

    Above motor, putting this all back together I find that the gray tach wire dead ends before it gets to the motor with a spade terminal on the end.... I've no idea where its supposed to go to get signal for the tach, all existing when i bought the boat, IE the tach and the wire, but the motor...
  12. R

    Throttle/Shift safety wiring?

    Have a throttle/shift setup, has TNT with it. Have those wires ID'd no problem. There is a micro looking switch inside the unit, has 2 wires coming out of it. Have no clue where they go to. Boat was bought torn apart.... I'm guessing a kind of neutral switch?? Where do they go and how to...
  13. R

    Wires in Throttle/Shift Control

    Hi Have an older boat, had to get a newer motor, working through the wiring differences in the old harness and new motor is fun.... I'm getting to where I think I'm close to going and buying a battery and seeing what happens.... Anyway I have a throttle/shift setup the way we bought the boat...
  14. R

    Wire color codes

    Need to extend/re-run wires for some stuff on a used boat. Any generic set of codes there as to colors? I know lights are blue, but I've got to do things like sending wire from fuel gauge, sending from Tach, and bilge and aerator wires, seems like my current "harness" is using gray for power...
  15. R

    My Own Battery Setup ?s

    I"ve thought it through and don't want a battery switch. I am going to wire one battery to the control box for the motor. The other on the other side of the boat will be for accessories. Here is what I come up with and input is welcome. I want to be able to disconnect both batteries when not...
See more
Top