Current visitors

Rugglesworth's latest activity

R

Rugglesworth replied to the thread Help me set up my new edelbrock 1409.

ok thanks that makes a lot of sense. This boat does have a large built in platform but is an inboard. I have some diaelectic grease so...

Yesterday at 11:40 AM
R

Rugglesworth reacted to Scott Danforth's post in the thread Help me set up my new edelbrock 1409 with Like.

8 degrees keeps the motor dummy proof from someone using 85 octane fuel with water in it (detonation) and keeps reversion at bay when...

Yesterday at 11:39 AM
R

Rugglesworth replied to the thread Help me set up my new edelbrock 1409.

I should also mention while I was adjusting the timing by moving the distributor (grabbing it by the top over the wires) I was shocked...

Yesterday at 11:18 AM
R

Rugglesworth replied to the thread Help me set up my new edelbrock 1409.

ok so I need a vacuum gauge for this procedure. I read on here 8 btdc was the right number but I guess 10 can't hurt. Is that a number...

Yesterday at 9:43 AM
R

Rugglesworth replied to the thread Help me set up my new edelbrock 1409.

ok I'll re time it to 10-12. I guess I should readjust my idle mixture screws back to factory settings first or does that matter?

Yesterday at 9:33 AM
R

Rugglesworth reacted to Scott Danforth's post in the thread Help me set up my new edelbrock 1409 with Like.

I would set base timing to 10-12 degrees BTDC You set idle in the water in gear

Yesterday at 9:32 AM
R

Rugglesworth replied to the thread Help me set up my new edelbrock 1409.

So fire it up, jumper wire on, take throttle connection off, adjust idle screw and then adjust throttle cable and reattach? Anything im...

Wednesday at 4:02 PM
R

Rugglesworth reacted to Pmt133's post in the thread Help me set up my new edelbrock 1409 with Like.

I set mine on the trailer but it behaved the same in the water. The service manual for TBV says to set in the water.

Wednesday at 4:01 PM
R

Rugglesworth replied to the thread Help me set up my new edelbrock 1409.

Ok I set it to approximately degrees and it idled a bit lower and rougher at about 575rpm as per the dash tachometer. I don't have a...

Wednesday at 3:42 PM
R

Rugglesworth replied to the thread Help me set up my new edelbrock 1409.

Ok so I grounded the purple wire to set base timing, hooked up the timing gun to cylinder 1, got her up to tell and then checked the...

Wednesday at 3:19 PM
R

Rugglesworth reacted to Scott06's post in the thread Help me set up my new edelbrock 1409 with Like.

The over flow fuel line on the intake helps the fire start faster, so you don’t waste time just getting a whiff of smoke… the marine...

Tuesday at 8:30 AM
R

Rugglesworth replied to the thread how to set up 1998 Ski Ray tournament inboard for wakeboarding.

like this one...

Monday at 3:44 PM
R

Rugglesworth posted the thread can I use this pump with a hose attached to fill and drain a ballast bag? in Wakeboarding, Wakesurfing, and Wakeskating.

I picked up an old 900 lb launch pad bench ballast bag. Can I use something like this to fill and drain the bag...

Monday at 2:09 PM
R

Rugglesworth replied to the thread how to set up 1998 Ski Ray tournament inboard for wakeboarding.

I just picked up an old Launch Pad 900lb bag for $50. No pump. Is there a universal style pump that I can use to fill and drain the bag?

Monday at 11:45 AM
R

Rugglesworth replied to the thread Help me set up my new edelbrock 1409.

yeah 100 Yes 100%. The yellow fail safe fuel line was just laying on the intake.... Carb was corroded, linkage was all gummed up and...

Monday at 10:14 AM

Show older items

Home
Members

Top

View All

View All

View All

View All

View All

View All

View All

View All

Boat Bimini Tops

Boat Covers

View All

View All

View All

View All

View All

View All

View All

Rugglesworth's latest activity

Follow Us