Current visitors

Scott06's latest activity

Scott06 reacted to alldodge's post in the thread Problems starting after fuel filter/water separator change with Like.

Assuming this was a blue or white spark (3/8 gap) and it repeated this spark several times as engine was cranking What we know; Have...

Today at 11:44 AM
Scott06 replied to the thread Problems starting after fuel filter/water separator change.

Id defer to AD but would be thinking confirm injectors are opening does it cough if starting fluid is shot in there ?

Today at 9:34 AM
Scott06 replied to the thread salt water in single cylinder.

Would think the last one is related to detonation

Today at 7:41 AM
Scott06 replied to the thread Problems starting after fuel filter/water separator change.

At this point no you have enough fuel pressure that is should start. So at this point find out why its not starting. could be lack of...

Yesterday at 1:22 PM
Scott06 replied to the thread Problems starting after fuel filter/water separator change.

anti-siphon valve or clog in puck up tube, some have screes in them. I would check for spark first as there is fuel to the rail so...

Yesterday at 10:21 AM
Scott06 replied to the thread I have to do a gimbal bearing and bellows etc, I have a question regarding the shift cable. Merc A1 G1 3.0.

yes in theory. I would inspect it carefully , assuming its in good shape reuse it. This is what I did when changing my bellows 3 years...

Yesterday at 10:19 AM
Scott06 replied to the thread Problems starting after fuel filter/water separator change.

I think fuel pressure should be 40-43 psi not 30. I would assume it would still start with only 30 psi so this may not be the issue at...

Yesterday at 4:55 AM
Scott06 replied to the thread Mercruiser dies after getting on temp.

he is referring to the rotor inside the distributor. If it has cracks the spark energy can go to ground instead of through the cap/wires...

Thursday at 2:09 PM
Scott06 replied to the thread Mercruiser 470 oil pump.

it should i have also done it by running it on the starter with the plugs out.

Thursday at 2:07 PM
Scott06 replied to the thread Mercruiser dies after getting on temp.

when it dies are you missing spark or gas ? if you dump a little gas down carb can you keep it running ? do you loose spark - put...

Thursday at 1:47 PM
Scott06 replied to the thread Mercruiser 470 oil pump.

I would not put sealant that could get squeezed into the oil passages and potentially block flow ...

Thursday at 1:43 PM
Scott06 replied to the thread Mercruiser dies after getting on temp.

you can ohm test the coil to see if it is off spec attched is a snip from specs on an aftermarket coil for your engine Would assume...
Thursday at 12:39 PM
Scott06 replied to the thread Problems starting after fuel filter/water separator change.

if you take a rag and push the schrader in with a small screw driver - you can quickly see if there is air there or not. if its fuel or...

Thursday at 12:31 PM
Scott06 replied to the thread I have to do a gimbal bearing and bellows etc, I have a question regarding the shift cable. Merc A1 G1 3.0.

Clicked the wrong one, didn’t think it was a hanging offense …sorry

Wednesday at 5:44 PM
Scott06 replied to the thread I have to do a gimbal bearing and bellows etc, I have a question regarding the shift cable. Merc A1 G1 3.0.

I didn’t have to cut my cable , just took the end off the shift plate end pulled inner completely out the bellhousing with weed walker...

Wednesday at 5:31 PM

Show older items

Home
Members

Top

View All

View All

View All

View All

View All

View All

View All

View All

Boat Bimini Tops

Boat Covers

View All

View All

View All

View All

View All

View All

View All

Scott06's latest activity

Follow Us