Recent content by SeaRyan

  1. S

    Gelcoat repair.

    I would like to know if anyone has tried a one step gel coat product, like FIBERGLASS EVERCOAT ONE STEP GEL COAT, before to repair gel coat. I have a couple of scratches not to the glass and 2 gashes about 2 and1/2 inches x 1/2 inch in size where you can see the glass but no glassepair is...
  2. S

    gimbal bearing

    Is an Alpha 1 Gen 1 gimbal bearing the same one used in an Alpha 1 Gen 2 drive? :confused:
  3. S

    Gimbal Bearing?

    I had posted awhile back about receiving a gimbal beearing from amarket.com and had stated that it looked different then the one I have in my Gen 2 transom. I was told that a Gen 1 is probably what I had received and needed a Gen 2. I spoke to Amarket and they said that they are the same gimbal...
  4. S

    Update (AMARKET. com gone) Bellows/Gimbal Bearing

    91 Mercruiser V6 4.3<br /><br />Quick question, I ordered a Transom repair kit from amarket.com and when I got it I notice that the Bearing look a different then the one in my boat. The center sticks out about 1/4 inch more and also the bellows that were in my boat were both rubber and what...
  5. S

    St. louis MO / IL

    Is there anyone in this area that might have a 3 jaw slap hammer that I can borrow to remove a gimbal bearing. :confused: <br /><br /><br />Thanks
  6. S

    Gel coat

    I have a spider web crack about 2 1/2 inches in diameter.This is on a hull that is a high glossy white and no other imperfection on hull.I check this link out{http://www.diynet.com/diy/bo_maintenance_repair/article/0,2021,DIY_13718_2278093,00.html) and it seems like a lot of work for some...
  7. S

    UPDATE:

    [No message]
  8. S

    4 months Vinyl stained

    This Sucks after spending 4 months of spare time with mine dad reupholstering my boat white. I put my brand new RED boat cover on the boat and we took it to the lake. After leaving the lake it rained and the @$#@%$ boat cover bled all over the vinyl any ideas on how to take it out would be...
  9. S

    idling issue

    91 I/O Mercruiser V6 4.3L <br /><br />When bringing my throttle back to neutral the new throttle cable sits at a high idle and I have pull the cable on the engine back to put it in idle.Not sure why?
  10. S

    Replaced Shifter cable same issue

    91 Mercruiser V6 4.3L I/O<br /><br />My remote was very hard to move both in reverse and forward. I had the shifter cable replaced from engine to outdrive but remote still stiff. If I remove the 2 cable from the engine that run to the remote I have no problem moving both in reverse and forward...
  11. S

    Throttle Shifting

    Mercruiser 4.3 L V6<br />Alpha 1 Gen 2 outdrive<br /><br />My shifting in both foward and reverse is very stiff. If I detach the cable from the engine it shifts very smooth so it doesn't look like it's the cable.If I just hook up the two throttle cables it's a little stiffer but not as bad as...
  12. S

    Fuel tank

    Can the fitting on a fuel tank where the hose connects from the tank to the fuel pump be replaced because for some reason it is not letting fuel into the pump.
  13. S

    Mercruiser Trim issue

    I have a Trim switch on my remote control that control both up and down and trailer but for some reason the trim will only go up about 3 or 4 inches off the ground and won't go up far enought to trailer not sure why. I replace the trim motor, soleniods and all for other reasons.Here's a picture...
  14. S

    Mercruiser Trim issue

    I have a Trim switch on my remote control that control both up and down and trailer but for some reason the trim will only go up about 3 or 4 inches off the ground and won't go up far enought to trailer not sure why. I replace the trim motor, soleniods and all for other reasons.Here's a picture...
  15. S

    Foam for Seats

    I'm refinishing a 91 SeaRay 170 and would like some suggestions on websites to get some good dense form for my seats.
See more
Top