Looking for a small basic aluminum boat to give my son for his first birthday to have something he can grow up with over the years as he gets older- maybe pass to his kids one day. I was on a very small lake growing up and still have my 12ft aluminum Myers Jon boat with a 6hp from when I was a...
84 35hp Merc - I have worked on this for several hours over two nights... I can get the crank and everything to line up but cant get the shift shaft splines to line up allowing the lower unit to go up the rest of the way. Is this a 2 person job? The rod from the motor has a ton of play side...
I have a 84 35hp twin cylinder outboard that I am trying to pull the lower end on to change the water pump. I removed all 4 bolts including the bold under the trim tab and can get the lower unit to drop down about 2 inches but it seems to stop there and wont come out any further. I cant seem...
I am a bit confused... maybe someone can help explain this motor to me. Its a 83 30hp Mariner that is pretty clearly Yamaha built... even has the yamaha logo right on the block. Every time I go to a yamaha dealer they argue that they do not sell parts for this outboard and I need to go...
Hello,
I have a 1984 35 hp Mercury that I am trying to replace the impeller in. I see all the bolts to remove the lower unit but I do not see a way to disconnect the shift rod for removal. Where is this done at? most outboards I have worked on in the past had a bolt that would disconnect the...
I am trying to setup a Tiny tach to work with my 08 2 stroke 25hp Yamaha.... I need to know when the ignition fires to get an accurate reading so I can be sure I have the correct prop on it.
The Tiny Tach has the option of the following degrees
45
60
90
120
180
360
720
How many sparks per...
I have a 2008 yamaha 2 stroke that I purchased last year and would like to hook up a tach to verify RPM @ WOT.... is there a easy way to connect a tach to this motor? is there anything special I will need to buy? I was thinking of getting a teleflex (or other brand) tach and speedo to mount in...
Hello,
looking to get a new bow mount trolling motor for my boat.... thinking around 40lbs thrust.
anyone know where to get a good deal on a new one?
What brand is best?
any good online stores?
Thanks
I just purchased a new 2 stroke 25hp Yamaha Elec start tiller outboard for my Polar V142T 14ft boat.... just hope it will be enough power.
just wondering what other people have thought of this motor?
Our 05 50hp lower unit fluid seems to disappear over the season? we fill the lower end at the start of the season all the way to the top and at the end of the season there is no water in the fluid but there seems to only be about half as much lube in the lower unit?.. any idea where it might be...
Anyone know of any dealers anywhere in the US with new old stock outboards that will ship them?
Looking for
25 ? 40 hp
Tiller
Trim/tilt
Electric start
Trying to find the best price around? anyone know of any close outs?
any brand is fine
I have a 1985 Evinrude 90hp with some buzzer issues. If I walk up and turn the key to the on position without even starting the motor sometimes the overheat buzzer will go off. It seems to sound from time to time with the motor running or not. It will stay steady for typically a few min then...
I was wondering if the 1985 90 HP V-4 Eninrude is prop or crank rated at 90HP?
what about a 1990 90 HP V-4 Johnson
I currently run a 85 90hp evinrude but was given a very nice 1990 90hp Johnson and may make a swap... just wondering if they are both prop rated?
what year did they start to...
I am about to change the thermostat on my 1985 E90MLCOS V4 Evinrude and would like to know what all I should replace... it looks like this motor has 2 thermostats? can I just change the 2 or do I need to replace anything else while I am in there?
